[SOLVED] P146F Code: Fast Fix For Evap Pressure Sensor

OBD code P146F indicates a fault with the Evaporative Emission Purge Pump system.

Symptoms include the Engine Light being ON.

The issue is commonly caused by a faulty purge pump, open/shorted harness, poor electrical connection, or a faulty ECM.

This code should be addressed promptly to prevent emissionsrelated problems.

A possible fix involves inspecting and repairing any damaged components or wiring connections related to the purge pump system.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!

The vehicle may experience a lack of power or acceleration under load with fault code P146F.

  • Symptoms: Engine Light ON.
  • Reduced engine power.
  • Rough idle.
  • Engine stalling.
  • Loss of acceleration.

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

P146F code typically indicates an issue with the exhaust gas recirculation (EGR) system.

  • P146F can be caused by a faulty Evaporative Emission Purge Pump.
  • An open or shorted Evaporative Emission Purge Pump harness.
  • A poor electrical connection in the Evaporative Emission Purge Pump circuit.
  • Or a faulty Engine Control Module (ECM).

To address fault code P146F, inspect the turbocharger boost control system for potential issues.

  • To fix OBDII code P146F, start by reviewing the possible causes related to this code.
  • Visually inspect the wiring harness and connectors associated with the component mentioned in the diagnostic trouble code.
  • Check for any damaged components and ensure the connector pins are not broken, bent, pushed out, or corroded.
  • If no issues are found during the visual inspection, proceed to test the component itself for proper operation.
  • Replace the component if necessary.
  • Clear the fault code from the vehicle’s computer using a scan tool.
  • Test drive the vehicle to verify the repair and ensure the code does not return.

Diagnosing and repairing fault code P146F may involve inspecting and servicing the vehicle’s exhaust gas recirculation system.

The cost to diagnose and fix OBD code P146F depends on the estimated 1. 0hour repair time.

Labor rates usually range from $75 to $150 per hour, so the total cost could be between $75 and $150. Factors like shop rates and the complexity of the repair can influence the final cost.

P146F code indicates an issue with the oil pressure control solenoid circuit in the engine.

OBD code P146F means that a fault has been detected in the exhaust gas recirculation (EGR) cooler bypass control circuit.

This code is triggered by the engine control module (ECM) when it detects a problem with the EGR cooler bypass control circuit.

The EGR cooler bypass control circuit is responsible for regulating the flow of exhaust gases through the EGR cooler to help reduce emissions.

When this circuit malfunctions, it can affect the performance and emissions of the vehicle.

This code indicates a fault with the oil pressure control solenoid in the engine.

OBDII code P146F relates to an issue with the transmission control module (TCM).

To diagnose this, check TCM power and ground using a multimeter.

Verify TCM communication over the Controller Area Network (CAN) using a scan tool.

If the TCM does not respond, reprogramming or reflashing may be necessary.

Visually inspect the wiring harness and connectors for any damage, and ensure connector pins are not broken, bent, pushed out, or corroded.

This thorough inspection can help pinpoint the root cause of the problem.

1. What does OBD code P146F indicate in a vehicle?

OBD code P146F indicates an issue with the Evaporative Emission Purge Pump system. Check for faulty pump, wiring, or ECM. Inspect and repair as needed.

2. What are the common symptoms associated with code P146F?

Common symptoms for code P146F include Engine Light ON, caused by issues like a faulty Evaporative Emission Purge Pump or ECM. Inspect wiring and connectors for damage.

3. How can I diagnose and repair OBD code P146F in my vehicle?

Diagnose and repair OBD code P146F by checking for a faulty Evaporative Emission Purge Pump, harness issues, or ECM problems. Inspect wiring and connectors for damage or corrosion.

 p146f error fault code explained

If your vehicle displays OBD code P146F, you may experience issues with the exhaust gas recirculation (EGR) system.

This could be caused by a faulty EGR valve, clogged EGR passages, or a malfunctioning EGR temperature sensor.

To address OBD code P146F, start by inspecting the EGR valve and its passages for any blockages.

Test the EGR temperature sensor for proper operation and check the wiring harness and connectors for any damage or corrosion.

Replace any faulty components as needed to resolve the issue.

Scroll to Top