The automobile fault code U2614 indicates a problem with the Drive Motor 2 Control Module or its related wiring harness and connectors. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code could be a faulty Drive Motor 2 Control Module, an open or shorted harness, or a poor electrical connection.
The importance of repairing this issue lies in the fact that it affects the performance of the vehicle’s hybrid or electric powertrain. The repair difficulty is moderate, and it takes around 1.0 hour to fix. To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors for any damage or corrosion.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Decoding U2614: Common Symptoms Of This Auto Fault Code
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the u2614 fault code.
Here are the symptoms to look out for:
- The automobile fault code U2614 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U2614: Common Causes Of This Fault Code
The automobile fault code u2614 can be caused by various factors, including a faulty drive motor control module and poor electrical connections.
- The automobile fault code U2614 can be caused by a faulty Drive Motor 2 Control Module.
- It can also be caused by an open or shorted Drive Motor 2 Control Module harness.
- Another possible cause is a poor electrical connection in the Drive Motor 2 Control Module circuit.
- Lastly, a faulty Hybrid/EV Powertrain Control Module 2 can also trigger this fault code.
Fix U2614: Quick Steps To Solve The Issue
Below are some possible fixes for the automobile fault code u2614, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u2614, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Cracking The Code: Cost And Complexity Of U2614 Fix
The factors that influence the cost of diagnosing and fixing the automobile fault code U2614 based on the repair time are: – Estimated repair time is 1.0 hour. – Auto repair shops usually charge between $75 and $150 per hour. – The complexity of the issue may affect the repair time and cost. – The type of vehicle and its make and model can also impact the cost. – The location of the repair shop and the availability of parts can also affect the cost.
U2614: Unresponsive Communication With Steering Angle Sensor
The u2614 fault code is related to the loss of communication with the HybridEV Powertrain Control Module 2. This diagnostic is used to check the communication status of the HybridEV Powertrain Control Module 2. The Battery Energy Control Module supervises a periodic serial data message to check the communication status.
If this message is not received within 400 ms, the Battery Energy Control Module increases its fail count. The DTC will set when a supervised periodic message that includes the transmitter device availability has not been received within 400 ms.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u2614 fault code. This code is caused by a faulty drive motor 2 control module, an open or shorted harness, poor electrical connection, or a faulty hybrid/EV powertrain control module 2. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the u2614 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, there are a few things you can do to fix it. First, check the possible causes, which include a faulty Drive Motor 2 Control Module, an open or shorted harness, poor electrical connection, or a faulty Hybrid/EV Powertrain Control Module 2. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
The u2614 fault code, indicated by the engine light or service engine soon warning light, may be caused by a faulty Hybrid/EV Powertrain Control Module 2. Other possible causes include a faulty Drive Motor 2 Control Module, open or shorted harness, or poor electrical connection. To fix the issue, inspect the wiring harness and connectors for any damage or corrosion, and check for broken or bent pins.
Wrap Up
If your engine light is on, it could be due to a faulty Drive Motor 2 Control Module or poor electrical connection. Check the wiring harness and connectors for damage and inspect the components for any issues. Take action to fix the problem as soon as possible.
