The automobile fault code U1901 indicates a problem with the Stability Control Sensor Cluster in the Anti-Lock Brake System (ABS). This is usually accompanied by the ABS warning light and the engine light turning on.
The cause of this fault code could be a faulty sensor cluster, an open or shorted harness, or a poor electrical connection. It is important to address this issue promptly as it can affect the vehicle’s stability and safety.
The repair process involves visually inspecting the wiring harness and connectors for any damage or corrosion and checking for broken or bent pins.
The repair time for this issue is estimated to be around 1.0 hour.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Decoding U1901: Common Symptoms Of This Fault Code
If you notice the ABS warning light and engine light on, it could be a sign of the U1901 fault code.
- The automobile fault code U1901 has two main symptoms.
- The first symptom is the Anti-Lock Brake System (ABS) Warning Light being ON.
- The second symptom is the Engine Light being ON or the Service Engine Soon Warning Light being ON.
- It is important to note that these are the only symptoms associated with this particular fault code.
Decoding U1901: Common Causes Of The Fault Code
The automobile fault code u1901 can be caused by various issues, including a faulty stability control sensor cluster, open or shorted harness, and poor electrical connection.
- The automobile fault code U1901 can be caused by a faulty Stability Control Sensor Cluster.
- It can also be caused by an open or shorted harness of the Stability Control Sensor Cluster.
- Additionally, a poor electrical connection in the Stability Control Sensor Cluster circuit can also trigger this fault code.
Fix U1901: Quick Steps To Solve The Fault Code
To fix the u1901 automobile fault code, check the possible causes and inspect the related wiring harness, connectors, and components for damage.
- To fix the automobile fault code u1901, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1901 Repair Cost & Complexity
The automobile fault code U1901 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. Therefore, the total cost of diagnosis and fixing the U1901 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
Decoding U1901: Understanding The Mysterious Network Communication Error
The U1901 fault code indicates a problem with the CAN Network No. 2 Communication Bus.
This bus is responsible for transmitting signals from the stability control sensor cluster to the ABS module.
The stability control sensor cluster contains the yaw rate sensor, roll rate sensor, lateral accelerometer, and longitudinal accelerometer. If there is an open circuit or a short to power or ground on any of the four circuits, the ABS module will set a DTC. Additionally, if the sensor cluster is not mounted correctly, the ABS module will also set DTCs.
FAQ
The u1901 fault code in an automobile can be caused by a faulty stability control sensor cluster, an open or shorted harness, or a poor electrical connection in the cluster circuit. This can result in the ABS warning light and engine light turning on. To fix the issue, one should visually inspect the wiring harness and connectors for any damage or corrosion and check for broken or bent pins.
If the Anti-Lock Brake System (ABS) Warning Light and Engine Light are on, it could be due to a faulty Stability Control Sensor Cluster. To check for faults, inspect the related wiring harness and connectors for any damage or poor electrical connections. Look for broken, bent, pushed out, or corroded connector’s pins. This will help identify if the Stability Control Sensor Cluster harness is open or shorted, and determine the necessary fix.
If you’re experiencing an ABS warning light and an engine light on, it could be due to a faulty Stability Control Sensor Cluster or a poor electrical connection. To fix the u1901 fault code, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If you see the ABS warning light and engine light on, it could be due to a faulty stability control sensor cluster, open or shorted harness, or poor electrical connection. To fix it, visually inspect the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.
