If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to the automobile fault code: u1446. This code is caused by a faulty Heated Steering Wheel (HSW) Temperature Sensor, an open or shorted HSW Temperature Sensor harness, a poor electrical connection in the HSW Temperature Sensor circuit, a faulty Right Steering Switch, or a faulty Steering Control Module (SCM). The importance of repairing this issue lies in the fact that it can affect the functionality of your steering wheel.
The repair difficulty is moderate, with a repair time of 1.0.
To fix the issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U1446: Common Symptoms You Shouldn’t Ignore
If you see the Engine Light ON, it could be due to the u1446 fault code.
Here are some symptoms to look out for:
- The automobile fault code U1446 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1446: Common Causes Of The Fault Code
The automobile fault code u1446 can be caused by various factors, including a faulty heated steering wheel temperature sensor and a faulty steering control module.
- The automobile fault code U1446 can be caused by a faulty Heated Steering Wheel (HSW) Temperature Sensor.
- It can also be caused by an open or shorted Heated Steering Wheel Temperature Sensor harness.
- Another cause can be a poor electrical connection in the Heated Steering Wheel Temperature Sensor circuit.
- A faulty Right Steering Switch can also trigger this fault code.
- Lastly, a faulty Steering Control Module (SCM) can also be a cause of the U1446 fault code.
Fix U1446: Simple Steps To Get Your Car Running Again
Below are some possible fixes for the automobile fault code u1446, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u1446, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Cracking The Code: U1446 Repair Cost And Complexity
The automobile fault code U1446 has an estimated repair time of 1.0 hour.
The cost of fixing this fault code is influenced by the repair time.
Most auto repair shops charge between $75 and $150 per hour for their services. Therefore, the fixing cost of U1446 will depend on the hourly rate charged by the repair shop. It is important to consider these factors when budgeting for the repair of this fault code.
Unlocking The Mystery Of U1446 Fault Code
The U1446 code is related to the Heated Steering Wheel (HSW) Temperature Sensor. The sensor data is transferred from the Right Steering Switch to the Cluster Cabin Compartment Node (CCN) by way of the LIN bus. The code sets when the Heated Seat Module (HSM) does not receive the Heated Steering Wheel (HSW) Temperature Sensor Fault Signal from the Cluster (CCN) for more than two seconds.
The code is an Implausible Heated Steering Wheel Temperature Message Receive fault code.
FAQ
If you’re experiencing the u1446 automobile fault code, your engine light may be on. This could be due to a faulty Heated Steering Wheel (HSW) Temperature Sensor, an open or shorted HSW Temperature Sensor harness, a poor electrical connection in the HSW Temperature Sensor circuit, a faulty Right Steering Switch, or a faulty Steering Control Module (SCM). To fix the issue, check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and broken, bent, pushed out, or corroded connector pins.
If the Engine Light or Service Engine Soon Warning Light is ON, it could be due to a faulty Heated Steering Wheel Temperature Sensor. To check for faults, inspect the related wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector pins. Also, check the Right Steering Switch and Steering Control Module for faults.
If you’re experiencing the u1446 fault code in your automobile, you may notice the engine light is on. This could be due to a faulty Heated Steering Wheel Temperature Sensor, an open or shorted harness, poor electrical connection, a faulty Right Steering Switch, or a faulty Steering Control Module. To fix the issue, visually inspect the wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on and you have a faulty Heated Steering Wheel Temperature Sensor, check the wiring harness and connectors for damage. Look for broken, bent, pushed out, or corroded connector pins.
Also, check the Right Steering Switch and Steering Control Module.