The automobile fault code U142C indicates a problem with the Active Exhaust Valve 2 Actuator, which can cause the engine light to turn on. The cause of this fault code could be a faulty actuator, an open or shorted harness, or a poor electrical connection. It is important to visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this fault code is estimated to be 1.0, and it is crucial to fix the issue to avoid any further damage to the vehicle.
To interpret the fault code, one should check the “Possible Causes” listed above and inspect the related components thoroughly.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
Decoding U142C: Unveiling Symptoms Of This Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u142c fault code.
Here are the symptoms to look out for:
- The fault code u142c can cause several symptoms in an automobile.
- These symptoms include the engine light turning on, the service engine soon warning light appearing, and the vehicle’s engine running poorly.
- Additionally, the car may experience reduced power or acceleration, and the transmission may shift roughly or erratically.
- The driver may also notice a decrease in fuel efficiency and an increase in emissions.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
Decoding U142C: Common Causes Of The Fault Code
The automobile fault code u142c can be caused by a faulty actuator or poor electrical connection.
- The automobile fault code u142c can be caused by a faulty Active Exhaust Valve 2 Actuator.
- It can also be caused by an open or shorted Active Exhaust Valve 2 Actuator harness.
- Additionally, a poor electrical connection in the Active Exhaust Valve 2 Actuator circuit can also trigger this fault code.
Fix U142C: Simple Steps To Solve The Issue
To fix the u142c automobile fault code, check the possible causes and inspect related components for damage or corrosion.
- To fix the automobile fault code u142c, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U142C Repair Cost & Complexity
The automobile fault code U142C can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of diagnosis and fixing the U142C fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time.
U142C: Lost Communication With Steering Angle Sensor
The Active Exhaust Valves reduce exhaust noise to meet regulations. They consist of mechanical butterfly valves and smart actuators.
Actuators communicate with the Powertrain Control Module over a LIN Bus circuit. The PCM sends a position command to the actuators based on engine torque, rpm and vehicle speed. If the valve position doesn’t match a predetermined calibration, a performance code is set.
U142C Code is an implausible data received from the exhaust valve. The fault is reported to the PCM over the LIN Bus.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u142c fault code. This code is usually caused by a faulty active exhaust valve 2 actuator, an open or shorted actuator harness, or a poor electrical connection in the actuator circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Active Exhaust Valve 2 Actuator. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify if the Active Exhaust Valve 2 Actuator harness is open or shorted, or if the circuit has a poor electrical connection.
If you find damaged components or broken, bent, pushed out, or corroded connector’s pins during the inspection for the u142c fault code, you should visually inspect the related wiring harness and connectors. Check for any possible causes listed above and fix them accordingly. It is important to ensure that the Active Exhaust Valve 2 Actuator harness is not open or shorted and that the circuit has a good electrical connection.
Wrap Up
If your engine light is on and the fault code is u142c, it may be due to a faulty Active Exhaust Valve 2 Actuator or related wiring issues. Visually inspect the wiring harness and connectors for damage and check for broken or corroded pins. Take action accordingly.