The automobile fault code U1359 indicates a problem with the Control Module, which is setting the Diagnostic Trouble Code (DTC). The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code could be a faulty Control Module, an open or shorted Control Module harness, or a poor electrical connection in the Control Module circuit. The repair importance is high as it can affect the performance of the vehicle. The difficulty level of the repair is moderate, and it takes around 1.0 hour to fix.
To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U1359: Common Symptoms You Need To Know
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u1359 fault code. Here are the symptoms to look out for:
- The U1359 fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1359: Common Causes Of The Fault Code
The automobile fault code u1359 can be caused by a faulty control module, open or shorted harness, or poor electrical connection.
- The automobile fault code U1359 can be caused by a faulty control module that sets the diagnostic trouble code (DTC).
- It can also be caused by an open or shorted control module harness.
- Additionally, a poor electrical connection in the control module circuit can also trigger this fault code.
Fix U1359: Simple Steps To Solve The Issue
Below are some possible fixes for the automobile fault code u1359, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u1359, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1359 Repair Cost & Complexity
The automobile fault code U1359 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. Therefore, the total cost of diagnosing and fixing the U1359 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
Decoding U1359: Understanding The Cause Of Ignition Input Circuit Failure
The U1359 code is related to the Local Interconnect Network (LIN) Bus.
It occurs when there is a loss of serial data communication between the master control module and the Transmission Range Indicator. The LIN Bus is a single wire with a transmission rate of 10.417 Kbits.
If the master control module detects a loss of communication, it will set a Diagnostic Trouble Code (DTC) for the non-communicating LIN device. The U1359 code sets when a supervised periodic message that includes the transmitter device availability has not been received.
FAQ
If your engine light is on and you’re seeing the u1359 fault code, it could be due to a faulty control module setting the diagnostic trouble code (DTC), an open or shorted control module harness, or a poor electrical connection in the control module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the u1359 fault code, which is indicated by the engine light or service engine soon warning light turning on, there are a few things you can do to fix it. The cause of this issue could be a faulty control module setting the diagnostic trouble code, an open or shorted control module harness, or a poor electrical connection in the control module circuit. To address these issues, you should visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.
If you find broken, bent, pushed out, or corroded connector’s pins while fixing the u1359 fault code, follow these steps. First, visually inspect the related wiring harness and connectors. Second, check for damaged components. Third, look for broken, bent, pushed out, or corroded connector’s pins. Finally, replace or repair any damaged components or connector pins to fix the issue.
Wrap Up
If your engine light is on and the diagnostic trouble code (DTC) is u1359, it may be caused by a faulty control module or poor electrical connection. To fix it, visually inspect the wiring harness and connectors for damage or corrosion. Check for broken or bent pins.
