The automobile fault code U1347 indicates a problem with the control module, which can trigger the engine light or service engine soon warning light. The cause of this issue can be a faulty control module setting the diagnostic trouble code, an open or shorted control module harness, or a poor electrical connection in the control module circuit.
The importance of repairing this fault code lies in the fact that it can affect the performance of the vehicle. The repair difficulty is moderate, and it takes around 1.0 hour to fix. To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors for any damage or corrosion.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Unveiling U1347: Symptoms Of A Troubled Automobile
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u1347 fault code. Here are the symptoms to look out for:
- The U1347 fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light, ABS Light ON, Traction Control Light ON, Brake Light ON, Speedometer not working, Cruise Control not working, and Transmission shifting problems.
Decoding U1347: Common Causes Of The Fault Code
The automobile fault code U1347 can be caused by a faulty control module, open or shorted harness, or poor electrical connection.
- The automobile fault code U1347 can be caused by a faulty control module that sets the diagnostic trouble code (DTC).
- It can also be caused by an open or shorted control module harness.
- Additionally, a poor electrical connection in the control module circuit can also trigger this fault code.
- These are the three main causes of the U1347 fault code in automobiles.
Fix U1347: Simple Steps To Solve The Issue
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Below are some possible fixes for the automobile fault code u1347, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u1347, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1347 Repair Cost & Complexity
The automobile fault code U1347 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of diagnosis and fixing the U1347 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
Unlocking The Mystery Of U1347: Your Car’s Electrical System
The U1347 fault code is related to the Engine Control Module (ECM) LIN Bus.
The Local Interconnect Network (LIN) Bus is a single wire transmission system with a rate of 10.417 Kbits. The LIN circuit is used to transmit serial data between the master control module and other LIN devices within a subsystem. If the master control module loses communication with any of the LIN devices on the network, it will set a no communication code against the non-communicating device.
The U1347 code sets when the ECM does not receive a supervised periodic message that includes the transmitter device availability.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u1347 fault code. This code is usually caused by a faulty control module setting the diagnostic trouble code (DTC), an open or shorted control module harness, or a poor electrical connection in the control module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the U1347 fault code, which is indicated by the engine light or service engine soon warning light turning on, there are a few things you can do to fix it. The cause of this issue could be a faulty control module setting the diagnostic trouble code, an open or shorted control module harness, or a poor electrical connection in the control module circuit. To address this problem, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
Ignoring the u1347 fault code can lead to serious consequences such as reduced fuel efficiency, engine misfires, and even engine failure. The fault code indicates a problem with the control module, which can cause the engine light to turn on. It is important to fix the issue in a timely manner by visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken or corroded pins.

Wrap Up
If your engine light is on and showing the u1347 code, check for a faulty control module, open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion.
Look for broken, bent, or pushed out connector pins.