The automobile fault code U1325 indicates a problem with the Automatic Back Door Control Module, which can cause the engine light to turn on. The cause of this issue can be due to faulty configuration work or a defective module.

It is important to address this issue promptly as it can affect the performance of the vehicle. The repair process involves visually inspecting the wiring harness and connectors for any damage or corrosion.

The repair time for this issue is estimated to be around 1.0.

To interpret the fault code, it is recommended to check the “Possible Causes” listed above and perform a thorough inspection of the related components.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

Unveiling U1325: Common Symptoms You Should Know

If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u1325 fault code.

Here are the symptoms to look out for:

The automobile fault code U1325 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON, ABS Light ON, Traction Control Light ON, and the speedometer may not work properly.
These symptoms indicate a communication error between the ABS module and the engine control module.
It is important to get this issue diagnosed and fixed as soon as possible to avoid any potential safety hazards while driving.

Decoding U1325: Common Causes Of The Fault Code

The automobile fault code u1325 can be caused by configuration work or a faulty control module.

The automobile fault code U1325 can be caused by configuration work of the Automatic Back Door Control Module.
It can also be caused by a faulty Automatic Back Door Control Module.
These are the only two known causes of this particular fault code.

Fix U1325: Simple Steps To Get Your Car Running Again

To fix the u1325 automobile fault code, check the possible causes and inspect the wiring harness, connectors, and components for damage.

To fix the automobile fault code u1325, first, check the possible causes listed above.
Then, visually inspect the related wiring harness and connectors.
Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
This fix will take an estimated repair time of 1.0 hour.

Crunching The Numbers: U1325 Fixing Cost & Complexity

The automobile fault code U1325 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.

Therefore, the total cost of diagnosis and fixing the U1325 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.

Decoding U1325: Understanding Your Vehicle’s Abs Communication Error

The U1325 fault code is related to the calibration of the Automatic Back Door Control Module.

This code is triggered when the calibration of the Automatic Back Door position information work is not successful.

The Diagnostic Trouble Code (DTC) sets when this calibration fails. The U1325 code indicates that there is an issue with the calibration of the Automatic Back Door Control Module. This fault code needs to be diagnosed and fixed by a professional mechanic to ensure proper functioning of the Automatic Back Door.

FAQ

What are the possible causes of the u1325 automobile fault code that triggers the engine light or service engine soon warning light?

If you see the engine light ON or Service Engine Soon Warning Light, it could be due to the u1325 fault code. This code is triggered by the configuration work of the Automatic Back Door Control Module or a faulty module. To fix this issue, you need to visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.

How can one fix the u1325 automobile fault code related to the configuration work of the Automatic Back Door Control Module?

If you’re experiencing the u1325 fault code related to the Automatic Back Door Control Module configuration work, you may notice the engine light or service engine soon warning light is on. The cause of this issue could be a faulty Automatic Back Door Control Module. To fix it, start by visually inspecting the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins.

What steps should be taken to visually inspect the related wiring harness and connectors when troubleshooting the u1325 automobile fault code?

When troubleshooting the u1325 automobile fault code, start by checking the “Possible Causes” listed above. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help identify any faults in the Automatic Back Door Control Module configuration work or a faulty module.

Wrap Up

If your engine light is on and you have a u1325 fault code, check the Automatic Back Door Control Module configuration work and inspect the wiring harness and connectors for damage.

Look for broken, bent, pushed out, or corroded connector’s pins.

[SOLVED] Fixing U1325: Calibration For Automatic Back Door Control Module