If you see the engine light on or the service engine soon warning light, it could be due to a faulty Electronic Shift Module (ESM) or an open or shorted ESM harness. The U11E3 fault code indicates a problem with the ESM or the Controller Area Network Dedicated Powertrain (CAN-DPT) Bus.
It’s important to address this issue promptly as it can affect the vehicle’s performance. The repair time for this fault code is estimated to be around 1.0 hour.
To fix the issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Decode U11E3: Uncovering Symptoms Of This Fault Code
If you notice the Engine Light ON, it could be a sign of u11e3 fault code. Here are the symptoms to look out for:
- The automobile fault code U11E3 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U11E3: Common Causes
The automobile fault code u11e3 can be caused by a faulty ESM, open or shorted ESM harness, poor electrical connection, or CAN-DPT Bus issues.
- The automobile fault code u11e3 can be caused by a faulty Electronic Shift Module (ESM).
- It can also be caused by an open or shorted Electronic Shift Module (ESM) harness.
- Another cause can be a poor electrical connection in the Electronic Shift Module (ESM) circuit.
- Additionally, an open or shorted Controller Area Network Dedicated Powertrain (CAN-DPT) Bus can also trigger this fault code.
Fix U11E3 Code: Simple Steps To Get Your Car Running
To fix the u11e3 automobile fault code, check the possible causes and inspect related wiring harness, connectors, and components for damage.
- To fix the automobile fault code u11e3, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U11E3 Repair Cost & Complexity
The automobile fault code U11E3 has an estimated repair time of 1.0 hour. The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services.
Therefore, the fixing cost of U11E3 will range between $75 and $150, depending on the repair time required.
U11E3: Understanding The Mysterious Brake Control Module Communication Fault
The u11e3 fault code is related to the Controller Area Network (CAN) bus. It monitors the messages transmitted on the CAN bus and their validity. The code sets when the CAN-DPT bus messages are not received from the Electronic Shift Module (ESM) for two to five seconds.
The Diagnostic Trouble Code (DTC) indicates that the Transmission Control Module (TCM) has lost communication with the ESM on DPT CAN. This fault code can cause issues with the vehicle’s transmission and should be addressed promptly.
FAQ
If you’re experiencing the u11e3 fault code, your engine light may be on. This could be due to a faulty Electronic Shift Module (ESM), an open or shorted ESM harness, a poor electrical connection in the ESM circuit, or an open or shorted Controller Area Network Dedicated Powertrain (CAN-DPT) Bus. To fix the issue, check the possible causes listed above, visually inspect the wiring harness and connectors, and look for any damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light with the u11e3 fault code, it may be due to a faulty Electronic Shift Module (ESM), an open or shorted ESM harness, a poor electrical connection in the ESM circuit, or an open or shorted Controller Area Network Dedicated Powertrain (CAN-DPT) Bus. To fix this issue, visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re troubleshooting the u11e3 automobile fault code, start by checking for an illuminated Engine Light or Service Engine Soon Warning Light. The cause of this issue could be a faulty Electronic Shift Module (ESM), an open or shorted ESM harness, a poor electrical connection in the ESM circuit, or an open or shorted Controller Area Network Dedicated Powertrain (CAN-DPT) Bus. To fix the problem, visually inspect the related wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light with the u11e3 code, check the Electronic Shift Module (ESM) and its harness for any open or short circuits. Inspect the wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector’s pins.
