The automobile fault code U11C6 indicates a problem with the Transmission Control Module (TCM). The most common symptom is the Engine Light ON or Service Engine Soon Warning Light. The cause of this fault code could be a faulty TCM, an open or shorted TCM harness, or a poor electrical connection in the TCM circuit.
It is important to address this issue promptly as it can lead to transmission problems. The repair difficulty is moderate, and the repair time is estimated at 1.0 hour.
To fix the issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins. It is crucial to interpret the fault code correctly to avoid further damage to the vehicle.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
Decode U11C6: Unveiling Symptoms Of This Fault Code
If you notice the Engine Light ON, it could be a sign of u11c6 fault code.
Here are the symptoms to look out for:
- The automobile fault code U11C6 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U11C6: Common Causes
The automobile fault code u11c6 can be caused by a faulty TCM, open or shorted TCM harness, or poor electrical connection.
- The automobile fault code u11c6 can be caused by a faulty Transmission Control Module (TCM).
- It can also be caused by an open or shorted Transmission Control Module harness.
- Additionally, a poor electrical connection in the Transmission Control Module circuit can also trigger this fault code.
Fix U11C6 Code: Simple Steps To Get Your Car Running
To fix the u11c6 automobile fault code, check the possible causes and inspect related wiring harness and connectors for damage.
- To fix the automobile fault code u11c6, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U11C6 Repair Cost & Complexity
The fault code U11C6 indicates a communication issue between the vehicle’s control module and the fuel pump control module.
The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this issue can vary depending on the auto repair shop, but it is common for most shops to charge between $75 and $150 per hour.
Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
U11C6: Lost Communication With Steering Angle Sensor
The U11C6 fault code is related to the availability of engine torque signals. It checks the valid bit of static indicated engine torque signal, engine friction torque signal, and indicated driver torque request signal. If the signals are not available, the PCM sends a Signal Not Available (SNA) default value to the TCM, resulting in the U11C6 code being set.
This code indicates a lost engine torque request message.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u11c6 fault code. This code is usually caused by a faulty Transmission Control Module (TCM), an open or shorted TCM harness, or poor electrical connection in the TCM circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the u11c6 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, there are a few things you can do to fix it. The issue may be caused by a faulty Transmission Control Module (TCM), an open or shorted TCM harness, or a poor electrical connection in the TCM circuit. To address these potential causes, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
Ignoring the u11c6 fault code, which indicates a faulty Transmission Control Module (TCM) or poor electrical connection, can lead to serious consequences. The engine light will remain on, indicating a problem, and the vehicle may experience transmission issues. It is important to visually inspect the wiring harness and connectors, and check for damaged components to avoid further damage.
![u11c6 error fault code explained](https://carmodnerd.com/wp-content/uploads/2023/06/U11C6-error-fault-code.jpg)
Wrap Up
If your engine light is on, it could be due to a faulty Transmission Control Module (TCM), an open or shorted TCM harness, or poor electrical connection.
Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken, bent, or pushed out connector pins.