If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to the automobile fault code: u1162.
This code is typically caused by a faulty LiftgateEndgate Control Module (LGMEGM), an open or shorted harness, or poor electrical connection.
It’s important to visually inspect the related wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated at 1.0, making it a relatively quick fix.
To interpret the fault code, check the “Possible Causes” listed above.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unresponsive Accelerator? U1162 Could Be The Culprit
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of u1162 fault code.
Here are the symptoms to look out for:
- The automobile fault code U1162 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1162: Common Causes Of The Fault Code
The automobile fault code u1162 can be caused by various factors, including a faulty control module and poor electrical connections.
- The automobile fault code U1162 can be caused by a faulty Liftgate/Endgate Control Module (LGM/EGM).
- It can also be caused by an open or shorted Liftgate/Endgate Control Module harness.
- Additionally, a poor electrical connection in the Liftgate/Endgate Control Module circuit can also trigger this fault code.
Fix U1162: Quick Steps To Solve The Issue
Below are some possible fixes for the automobile fault code u1162, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u1162, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1162 Diagnosis Cost & Complexity
The automobile fault code U1162 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. Therefore, the total cost of fixing the U1162 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to diagnose and fix the issue.
Decoding U1162: Understanding Your Vehicle’s Network Communication Failure
The U1162 fault code is related to the class 2 serial data circuit in automobiles.
Modules in the circuit monitor for serial data communications during normal vehicle operation. When a module doesn’t receive a message for a critical operating parameter, it uses a default value for that parameter.
If a module doesn’t receive a Node Alive message from a learned identification number for 5 seconds, a Diagnostic Trouble Code (DTC) U1162 is set.
This fault code specifically indicates lost communications with the liftgateendgate control module.
FAQ
If you’re experiencing the u1162 fault code, your engine light may be on. This could be due to a faulty Liftgate/Endgate Control Module (LGM/EGM), an open or shorted harness, or poor electrical connection in the module circuit. To fix the issue, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a u1162 fault code, it could be caused by a faulty Liftgate/Endgate Control Module (LGM/EGM), an open or shorted harness, or a poor electrical connection. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.
If the Liftgate/Endgate Control Module harness is open or shorted, it can cause the u1162 fault code, which triggers the Engine Light ON or Service Engine Soon Warning Light. The faulty Liftgate/Endgate Control Module (LGM/EGM) or poor electrical connection in the Liftgate/Endgate Control Module circuit can also be the cause. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and you have a U1162 fault code, it may be due to a faulty LiftgateEndgate Control Module or a related wiring issue.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion and check for broken or bent pins.
