If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to the automobile fault code: u113c. This code indicates a problem with the Antilock Brake (ABS) Module, Antilock Brake Module harness, or the Drive Train Control Module (DTCM).
To fix the issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
The repair time for this issue is estimated to be around 1.0.
Understanding and interpreting fault codes is crucial for maintaining your vehicle’s health and preventing further damage.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Decode U113C: Unveiling Symptoms Of This Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u113c fault code.
Here are the symptoms to look out for:
- The automobile fault code U113C has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U113C: Common Causes Of The Fault Code
The automobile fault code u113c can be caused by a faulty ABS module, open or shorted ABS module harness, poor electrical connection in the ABS module circuit, or a faulty DTCM.
- The automobile fault code U113C can be caused by a faulty Antilock Brake (ABS) Module.
- It can also be caused by an open or shorted Antilock Brake Module harness.
- Another cause can be a poor electrical connection in the Antilock Brake Module circuit.
- Lastly, a faulty Drive Train Control Module (DTCM) can also trigger this fault code.
Fix U113C Code: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code u113c, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u113c, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U113C Repair Cost & Complexity
The automobile fault code U113C has an estimated repair time of 1.0 hour. The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services.
Therefore, the fixing cost of U113C will range between $75 and $150, depending on the repair time required.
U113C: Lost Communication With Steering Angle Sensor
The U113C code is a Diagnostic Trouble Code (DTC) that sets when the Drive Train Control Module (DTCM) does not receive a vehicle wheel speed signal from the Antilock Brake (ABS) Module over the Controller Area Network (CAN) C bus. This code indicates a lost wheel speed message, which means that the ABS Module is not communicating properly with other controllers over the CAN C bus. The DTCM continuously monitors the bus activity and receives the messages it needs, but when it doesn’t receive a wheel speed signal from the ABS Module, the U113C code is triggered.
This can cause issues with the vehicle’s braking system and should be addressed promptly.
FAQ
If you’re experiencing the u113c fault code, your engine light may be on. This could be due to a faulty Antilock Brake (ABS) Module, an open or shorted ABS Module harness, a poor electrical connection in the ABS Module circuit, or a faulty Drive Train Control Module (DTCM). To fix the issue, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a u113c fault code, there are a few possible causes to consider. These include a faulty Antilock Brake (ABS) Module, an open or shorted Antilock Brake Module harness, a poor electrical connection in the Antilock Brake Module circuit, or a faulty Drive Train Control Module (DTCM). To fix the issue, start by visually inspecting the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
A faulty Drive Train Control Module (DTCM) is listed as one of the possible causes of the u113c fault code, which triggers the Engine Light ON or Service Engine Soon Warning Light. To fix the issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty Antilock Brake Module, open or shorted harness, poor electrical connection, or a faulty Drive Train Control Module.
Check the possible causes, inspect wiring and connectors, and look for damaged components or corroded pins.
