The automobile fault code U1137 indicates a problem with the Digital Radio Receiver (DRR) in your vehicle. The most common symptom is the Engine Light turning on or the Service Engine Soon Warning Light. The cause of this issue could be a faulty DRR, an open or shorted DRR harness, or a poor electrical connection in the DRR circuit.
It is important to address this issue promptly as it can affect the performance of your vehicle. The repair time for this fault code is estimated to be around 1.0 hour.
To fix the problem, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U1137: Common Symptoms You Need To Know
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u1137 fault code.
Here are the symptoms to look out for:
- The automobile fault code U1137 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1137: Common Causes
The automobile fault code u1137 can be caused by a faulty DRR, open or shorted harness, or poor electrical connection.
- The automobile fault code U1137 can be caused by a faulty Digital Radio Receiver (DRR).
- It can also be caused by an open or shorted Digital Radio Receiver harness.
- Additionally, a poor electrical connection in the Digital Radio Receiver circuit can also trigger this fault code.
Fix U1137: Simple Steps To Solve The Fault Code
Below are some possible fixes for the automobile fault code u1137, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u1137, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1137 Repair Cost & Complexity
The automobile fault code U1137 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of fixing the U1137 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to diagnose and fix the issue.
Decoding U1137: Understanding The Abs Brake Pressure Sensor Circuit Failure
The U1137 code is related to the class 2 serial data circuit in automobiles. Modules in the circuit monitor for serial data communications during normal vehicle operation. When a module doesn’t receive a message for a critical operating parameter, it uses a default value for that parameter.
If a module doesn’t receive a Node Alive message from a learned identification number for 5 seconds, a Diagnostic Trouble Code (DTC) U1137 is set. This code indicates that there is a lost communication with the digital radio receiver.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u1137 fault code. This code is usually caused by a faulty digital radio receiver (DRR), an open or shorted DRR harness, or a poor electrical connection in the DRR circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the u1137 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you may have a faulty Digital Radio Receiver (DRR), an open or shorted DRR harness, or a poor electrical connection in the DRR circuit. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify the root cause of the problem and take the necessary steps to resolve it.
If you encounter damaged components or broken, bent, pushed out, or corroded connector’s pins while fixing the u1137 fault code, follow these steps. First, visually inspect the related wiring harness and connectors. Then, check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. Finally, fix the issue by replacing or repairing the damaged components or connector pins.
![u1137 error fault code explained](https://carmodnerd.com/wp-content/uploads/2023/06/U1137-error-fault-code.jpg)
Wrap Up
If your engine light is on, it could be due to a faulty Digital Radio Receiver (DRR), an open or shorted DRR harness, or poor electrical connection.
Visually inspect the wiring harness and connectors for damage or corrosion. Check for broken, bent, pushed out, or corroded connector’s pins.