The automobile fault code U112D indicates a problem with the Steering Column Control Module (SCCM).
The most common symptom is the Engine Light ON or Service Engine Soon Warning Light. The cause of this fault code could be a faulty SCCM, an open or shorted harness, or a poor electrical connection. It is important to address this issue promptly as it can affect the steering system’s performance.
The repair time for this issue is estimated to be around 1.0 hour. To fix this problem, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U112D: Common Symptoms You Shouldn’t Ignore
If you notice the Engine Light ON, it could be a sign of u112d fault code.
Here are the symptoms to look out for:
- The automobile fault code u112d has the following symptoms: Engine Light ON, Service Engine Soon Warning Light.
Decoding U112D: Common Causes Of The Fault Code
The automobile fault code u112d can be caused by various factors, including a faulty SCCM, open or shorted harness, and poor electrical connection.
- The automobile fault code u112d can be caused by a faulty Steering Column Control Module (SCCM).
- It can also be caused by an open or shorted Steering Column Control Module harness.
- Additionally, a poor electrical connection in the Steering Column Control Module circuit can also trigger this fault code.
Fix U112D: Simple Steps To Get Your Car Running Again
Below are the possible fixes for the automobile fault code u112d, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u112d, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U112D Repair Cost & Complexity
The automobile fault code U112D has an estimated repair time of 1.0 hour. The cost of fixing this code varies depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour. These factors are influential in determining the overall cost of fixing the U112D fault code.
U112D Fault Code: Lost Communication With Steering Angle Sensor
The u112d fault code is related to the Body Control Module (BCM) and the Steering Column Control Module (SCCM). This code sets when the BCM does not receive LIN Bus messages from the SCCM for more than three seconds. When this fault code appears, the Electronic Vehicle Information Center (EVIC) will not update.
The u112d code specifically indicates a lost communication with the EVIC Steering Wheel Switch.
FAQ
If your engine light is on and you’re seeing the u112d fault code, it could be due to a faulty Steering Column Control Module (SCCM), an open or shorted SCCM harness, or a poor electrical connection in the SCCM circuit. To fix the issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the u112d fault code, indicated by the Engine Light ON or Service Engine Soon Warning Light, it may be due to a faulty Steering Column Control Module (SCCM). To fix this issue, start by checking the possible causes listed above. Visually inspect the related wiring harness and connectors, looking for damaged components and broken, bent, pushed out, or corroded connector’s pins.
If you encounter the u112d fault code, which causes the engine light to turn on, you should visually inspect the related wiring harness and connectors. This fault code is caused by a faulty Steering Column Control Module (SCCM), an open or shorted SCCM harness, or a poor electrical connection in the SCCM circuit. To fix this issue, check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and you have a u112d fault code, it may be due to a faulty Steering Column Control Module (SCCM), an open or shorted harness, or poor electrical connection.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion and check for broken or bent pins.
