The automobile fault code U1108 indicates a problem with the Combination Meter, which can cause the Engine Light to turn on. This fault code can be caused by a faulty Combination Meter, an open or shorted Combination Meter harness, or a poor electrical connection in the Combination Meter circuit. It is important to visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this fault code is estimated to be 1.0.
To interpret the fault code, check the “Possible Causes” listed above and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U1108: Common Symptoms Of This Automobile Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be a sign of u1108 fault code.
Here are the symptoms to look out for:
- The automobile fault code U1108 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1108: Common Causes Of The Fault Code
The automobile fault code u1108 can be caused by a faulty Combination Meter, open or shorted Combination Meter harness, or poor electrical connection in the Combination Meter circuit.
- The automobile fault code u1108 can be caused by a faulty Combination Meter.
- It can also be caused by an open or shorted Combination Meter harness.
- Additionally, a poor electrical connection in the Combination Meter circuit can also trigger this fault code.
Fix U1108: Simple Steps To Get Your Car Running Again
To fix the u1108 automobile fault code, check the possible causes and inspect related wiring harness, connectors, and components for damage.
- To fix the automobile fault code u1108, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1108 Repair Cost & Complexity
The fault code U1108 indicates a communication error between the engine control module and the transmission control module.
The estimated repair time for this fault code is 1.0 hour. The cost of fixing this fault code varies depending on the hourly rate charged by the auto repair shop.
Most auto repair shops charge between $75 and $150 per hour.
Therefore, the cost of fixing the U1108 fault code can range from $75 to $150.
U1108: Unveiling The Mystery Behind Your Car’s Electrical System
The u1108 fault code is related to the Controller Area Network (CAN) bus lines between the combination meter and the transfer-ECU. This fault code may be triggered due to defective wiring harness or connector(s) in the CAN bus lines. The power supply system to the combination meter, the combination meter itself, or the transfer-ECU may also be the cause of the u1108 fault code.
The u1108 code specifically refers to the Combination Meter Time-Out E.
FAQ
If your engine light is on and you’re seeing the u1108 fault code, it could be due to a faulty combination meter, an open or shorted combination meter harness, or a poor electrical connection in the combination meter circuit. To fix the issue, visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the u1108 fault code with the engine light on, it could be due to a faulty combination meter, an open or shorted combination meter harness, or a poor electrical connection in the combination meter circuit. To fix this issue, start by visually inspecting the related wiring harness and connectors. Check for any damaged components and look for broken, bent, pushed out, or corroded connector pins. Don’t forget to check the possible causes listed above.
If you’re dealing with a u1108 fault code, keep an eye out for the engine light turning on. This could indicate a faulty combination meter, an open or shorted combination meter harness, or a poor electrical connection in the combination meter circuit. To fix the issue, visually inspect the wiring harness and connectors, and check for damaged components or broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on and the code is U1108, it’s likely due to a faulty combination meter, open or shorted harness, or poor electrical connection.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion and check for broken or bent pins.
