The automobile fault code U1058 indicates a problem with a module that is not communicating properly. This can cause the engine light to turn on, indicating a need for service.
The cause of this issue could be a faulty module, an open or shorted module harness, or a poor electrical connection in the module circuit. It is important to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated to be around 1.0, and it is crucial to address this problem promptly to avoid further damage to the vehicle.
To interpret the fault code, it is recommended to check the “Possible Causes” listed above and inspect the related components thoroughly.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U1058: Common Symptoms You Shouldn’t Ignore
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be a sign of u1058 fault code.
Here are the symptoms to look out for:
- The automobile fault code U1058 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1058: Common Causes Of The Fault Code
The automobile fault code u1058 can be caused by a faulty module, open or shorted module harness, or poor electrical connection.
- The automobile fault code U1058 can be caused by a faulty module that is not communicating.
- It can also be caused by an open or shorted module harness.
- Additionally, a poor electrical connection in the module circuit can also trigger this fault code.
Fix U1058: Quick Steps To Solve The Issue
Below are some possible fixes for the automobile fault code u1058, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u1058, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1058 Diagnosis Cost & Complexity
The automobile fault code U1058 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of fixing the U1058 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
Decoding U1058: Understanding The Cause Of Your Car’s Communication Failure
The U1058 fault code is related to the transmission or transaxle of the vehicle. It indicates that there is invalid or missing data being transmitted through the class 2 serial data circuit.
Modules in the vehicle monitor for serial data communications during normal operation.
If a module does not associate an identification number with at least one critical parameter within 5 seconds of beginning serial data communication, the U1058 DTC is set.
This fault code can cause the affected module to use default values for critical operating parameters.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u1058 automobile fault code. This code is usually caused by a faulty module that is not communicating, an open or shorted module harness, or a poor electrical connection in the module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the u1058 fault code, which is indicated by the engine light being on or the service engine soon warning light, there are a few things you can do to fix it. The cause of this issue could be a faulty module that is not communicating, an open or shorted module harness, or a poor electrical connection in the module circuit. To address this problem, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
If you’re dealing with the u1058 fault code, keep an eye out for the engine light turning on or the service engine soon warning light. The cause of this issue could be a faulty module that isn’t communicating, an open or shorted module harness, or a module circuit with poor electrical connection. To fix it, check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and you have a U1058 fault code, it could be due to a faulty module or poor electrical connection. Check the wiring harness and connectors for damage or corrosion. Look for broken, bent, or pushed out pins.
Inspect the components and fix any issues found.
