The automobile fault code U0464 indicates a problem with the Navigation Control Module. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code could be a faulty Navigation Control Module, an open or shorted Navigation Control Module harness, or a poor electrical connection in the Navigation Control Module circuit.
The importance of repairing this issue lies in the fact that it can affect the vehicle’s navigation system.
The repair difficulty is moderate, and the estimated repair time is 1.0 hour.
To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unresponsive Steering? U0464 Could Be The Culprit
If you notice the Engine Light ON, it could be a sign of u0464 fault code.
Here are the symptoms to look out for:
- The U0464 fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light, issues with the transmission, problems with the fuel system, difficulty starting the engine, reduced fuel efficiency, and rough idling.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving.
Decoding U0464: Common Causes Of The Fault Code
The automobile fault code u0464 can be caused by a faulty Navigation Control Module, an open or shorted harness, or poor electrical connection.
- The automobile fault code U0464 can be caused by a faulty Navigation Control Module.
- It can also be caused by an open or shorted Navigation Control Module harness.
- Additionally, a poor electrical connection in the Navigation Control Module circuit can also trigger this fault code.
Fix U0464: Simple Steps To Solve The Issue
Below are some possible fixes for the automobile fault code u0464, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u0464, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U0464 Fixing Cost & Complexity
The automobile fault code U0464 has an estimated repair time of 1.0 hour. The cost of fixing this fault code is influenced by the repair time.
Most auto repair shops charge between $75 and $150 per hour for their services. Therefore, the fixing cost of U0464 will range between $75 and $150, depending on the repair time required.
These factors should be considered when estimating the cost of fixing the U0464 fault code.
U0464: Understanding Your Vehicle’s Brake Control Module Communication Error
The U0464 code is related to the Navigation Control Module in a vehicle. It indicates that the receiving device has detected a discrepancy in the information it receives from the Navigation Control Module.
This discrepancy causes the integrity of the information to be questioned, resulting in an invalid data Diagnostic Trouble Code (DTC) being set.
The U0464 code is a Controller Area Network (CAN) fault code, which is a vehicle bus standard designed to interconnect automotive devices without a host computer.
FAQ
If the engine light is on with the automobile fault code u0464, it could be due to a faulty Navigation Control Module, an open or shorted Navigation Control Module harness, or a poor electrical connection in the Navigation Control Module circuit. To fix the issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the U0464 fault code, which is indicated by the engine light or service engine soon warning light turning on, there are a few things you can do to fix it. The cause of this issue could be a faulty Navigation Control Module, an open or shorted harness, or a poor electrical connection. To address this problem, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the U0464 fault code, start by checking the “Possible Causes” listed above. Then, visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Navigation Control Module harness and circuit connections.
Wrap Up
If your engine light is on, it could be due to a faulty Navigation Control Module or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken or bent pins. Take action to fix the issue.
