The automobile fault code U0247 indicates a problem with the Seat Control Module ‘F’ in your vehicle. The most common symptom is the Engine Light turning on. The cause of this issue could be a faulty module, an open or shorted harness, or a poor electrical connection.
It is important to address this issue promptly as it can affect the performance of your vehicle. The repair process involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.
The repair time for this issue is estimated to be around 1.0 hour.
To interpret the fault code, it is recommended to check the “Possible Causes” listed above.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Decoding U0247: Common Symptoms Of This Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be a sign of u0247 fault code.
Here are the symptoms to look out for:
- The automobile fault code U0247 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U0247: Common Causes Of The Fault Code
The automobile fault code U0247 can be caused by a faulty seat control module ‘F’, an open or shorted harness, or poor electrical connection.
- The automobile fault code U0247 can be caused by a faulty Seat Control Module ‘F’.
- It can also be caused by an open or shorted harness of the Seat Control Module ‘F’.
- Additionally, a poor electrical connection in the Seat Control Module ‘F’ circuit can also trigger this fault code.
Fix U0247: Simple Steps To Get Your Car Running Again
To fix the u0247 fault code, check the possible causes and inspect the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code u0247, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U0247 Repair Cost & Complexity
The automobile fault code U0247 has an estimated repair time of 1.0 hour.
The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services. Therefore, the fixing cost of U0247 will range between $75 and $150, depending on the repair time required.
These factors should be considered when estimating the cost of fixing the U0247 fault code.
U0247: Unleashing The Mystery Of Lost Communication With Body Control Module
The U0247 code is a Controller Area Network (CAN) fault code. CAN is a vehicle bus standard designed to interconnect automotive devices without a host computer.
The CAN bus uses two dedicated wires for communication, CAN high and CAN low.
The U0247 code sets when a periodic message from the Seat Control Module ‘F’ has not been received.
This code indicates that there is a lost communication with the Seat Control Module ‘F’.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u0247 fault code. This code is caused by a faulty seat control module ‘F’, an open or shorted harness, or a poor electrical connection in the circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the u0247 fault code, which is indicated by the engine light or service engine soon warning light being on, you may need to visually inspect the related wiring harness and connectors. This fault code can be caused by a faulty seat control module ‘F’, an open or shorted harness, or a poor electrical connection in the circuit. To fix the issue, check the possible causes listed above and inspect the wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the U0247 fault code, start by checking the possible causes: a faulty Seat Control Module ‘F’, an open or shorted harness, or a poor electrical connection in the circuit. To fix the issue, visually inspect the wiring harness and connectors, looking for any damaged components or broken, bent, pushed out, or corroded connector pins. Be thorough in your inspection to ensure you identify and address the root cause of the problem.
Wrap Up
If your engine light is on and the code is u0247, it could be due to a faulty Seat Control Module ‘F’, an open or shorted harness, or poor electrical connection.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion, and check for broken or bent pins.
