The automobile fault code U0214 indicates a problem with the Remote Function Actuation system, which can cause the engine light to turn on. The possible causes of this fault code include a faulty Remote Function Actuation, an open or shorted harness, or a poor electrical connection in the circuit.
To fix this issue, one should visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated to be around 1.0.
It is important to address this issue promptly to avoid any further damage to the vehicle. To interpret the fault code, one can use an OBD-II scanner or take the vehicle to a mechanic for diagnosis.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unresponsive Steering? U0214 May Be The Culprit
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of the U0214 fault code. Here are some symptoms to look out for:
- The U0214 fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light, issues with the transmission, problems with the ABS system, issues with the stability control system, problems with the traction control system, and issues with the cruise control system.
- It is important to address these symptoms promptly to avoid further damage to the vehicle.
Decoding U0214: Common Causes Of The Fault Code
The automobile fault code U0214 can be caused by various issues, including faulty remote function actuation and poor electrical connections.
- The automobile fault code U0214 can be caused by a faulty Remote Function Actuation.
- It can also be caused by an open or shorted Remote Function Actuation harness.
- Additionally, a poor electrical connection in the Remote Function Actuation circuit can also trigger this fault code.
Fix U0214: Simple Steps To Get Your Car Running Again
Below are the possible fixes for the automobile fault code U0214.
- To fix the automobile fault code U0214, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U0214 Repair Cost & Complexity
The automobile fault code U0214 has an estimated repair time of 1.0 hour. The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services.
Therefore, the fixing cost of U0214 will be between $75 and $150, depending on the repair time required.
U0214 Fault Code: Understanding Symptoms, Causes, And Fixes
The U0214 code is a Controller Area Network (CAN) fault code. CAN is a vehicle bus standard designed to interconnect automotive devices without a host computer. The U0214 code sets when a periodic message from the Remote Function Actuation has not been received.
This fault code indicates a lost communication with the Remote Function Actuation.
The Diagnostic Trouble Code (DTC) sets when this communication loss occurs.
The CAN bus is not sensitive to inductive spikes, electrical fields, or other noise.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u0214 fault code. This code is usually caused by a faulty remote function actuation, an open or shorted harness, or a poor electrical connection in the remote function actuation circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Remote Function Actuation or an open/shorted harness. To fix this issue, visually inspect the wiring harness and connectors related to the Remote Function Actuation. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any poor electrical connections and resolve the issue.
If you find damaged components or broken, bent, pushed out, or corroded connector’s pins during the inspection for the U0214 fault code, you should replace or repair them as necessary. This will help to ensure that the Remote Function Actuation circuit has a good electrical connection and that the fault code does not reoccur. Remember to visually inspect the related wiring harness and connectors as well, and check the “Possible Causes” listed above to ensure that all potential issues are addressed.
Wrap Up
If your engine light is on and the code is u0214, it could be due to a faulty Remote Function Actuation or an openshorted harness.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion. Check for broken or bent pins.
