The automobile fault code U016A indicates a problem with the Global Positioning System (GPS) module. The most common symptom is the illumination of the engine light or service engine soon warning light.
The cause of this fault code could be a faulty GPS module, an open or shorted GPS module harness, or a poor electrical connection in the GPS module circuit. The importance of repairing this issue lies in the fact that it can affect the accuracy of the vehicle’s navigation system.
The difficulty of the repair is moderate, with a repair time of 1.0.
To fix the issue, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
Unresponsive Steering? U016A Could Be The Culprit
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u016a fault code. Here are the symptoms to look out for:
- The U016A fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON, issues with the transmission, problems with the ABS system, issues with the stability control system, problems with the traction control system, and issues with the cruise control system.
- It is important to address these symptoms promptly to avoid further damage to the vehicle.
Decoding U016A: Common Causes Of The Fault Code
The u016a automobile fault code can be caused by various issues, including a faulty GPS module or poor electrical connections.
- The automobile fault code U016A can be caused by a faulty Global Positioning System (GPS) module.
- It can also be caused by an open or shorted GPS module harness.
- Additionally, a poor electrical connection in the GPS module circuit can also trigger this fault code.
Fix U016A Code: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code u016a, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u016a, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U016A Fixing Cost & Complexity
The automobile fault code U016A has an estimated repair time of 1.0 hour. The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services.
Therefore, the fixing cost of U016A will range between $75 and $150, depending on the repair time required.
U016A: Lost Communication With Vehicle Dynamics Control Module
The U016A code is a Controller Area Network (CAN) fault code. CAN is a vehicle bus standard designed to interconnect automotive devices without a host computer.
The U016A code sets when a periodic message from the Global Positioning System Module has not been received. The Diagnostic Trouble Code (DTC) indicates a lost communication with the Global Positioning System Module. CAN bus uses two dedicated wires for communication, CAN high and CAN low.
The CAN bus is not sensitive to inductive spikes, electrical fields, or other noise.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u016a fault code. This code is usually caused by a faulty Global Positioning System (GPS) module, an open or shorted GPS module harness, or a poor electrical connection in the GPS module circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Global Positioning System Module or an open or shorted harness. To fix this issue, visually inspect the related wiring harness and connectors for any damaged components or broken, bent, pushed out, or corroded connector’s pins. Check the “Possible Causes” listed above for further guidance.
If you find damaged components or broken, bent, pushed out, or corroded connector’s pins during the inspection for the u016a fault code, you should replace or repair them as necessary. This will help to ensure that the Global Positioning System Module is functioning properly and that the engine light or service engine soon warning light is turned off. Be sure to visually inspect the related wiring harness and connectors, and check for any other possible causes listed above.
Wrap Up
If your engine light is on, it could be due to a faulty Global Positioning System Module or poor electrical connection. Check the wiring harness and connectors for damage or corrosion.
Look for broken, bent, or pushed out pins.
Inspect the components listed under “Possible Causes.”