The automobile fault code U0156 indicates a problem with the Information Center Module ‘A’ in the vehicle. The most common symptom is the illumination of the engine light or service engine soon warning light. The cause of this fault code could be a faulty Information Center Module ‘A’, an open or shorted harness, or a poor electrical connection in the circuit.
It is important to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this fault code is estimated to be 1.0.
To interpret the fault code, it is recommended to check the possible causes listed above and inspect the related components thoroughly.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Unresponsive Dashboard? U0156 Explained
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u0156 fault code. Here are the symptoms to look out for:
- The fault code U0156 is associated with several symptoms, including the illumination of the engine light or service engine soon warning light.
- Other symptoms may include issues with the vehicle’s transmission, such as difficulty shifting gears or slipping gears.
- Additionally, the vehicle may experience problems with its speedometer or other gauges, such as inaccurate readings or complete failure.
- The vehicle’s fuel efficiency may also be affected, resulting in decreased gas mileage.
- Finally, the vehicle may experience issues with its electrical system, such as a dead battery or problems with the alternator.
Decoding U0156: Common Causes Of Fault Code
The automobile fault code u0156 can be caused by a faulty Information Center Module ‘A’, an open or shorted harness, or poor electrical connection.
- The automobile fault code U0156 can be caused by a faulty Information Center Module ‘A’.
- It can also be caused by an open or shorted Information Center Module ‘A’ harness.
- Additionally, a poor electrical connection in the Information Center Module ‘A’ circuit can also trigger this fault code.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fix U0156: Quick Steps To Solve The Fault Code
Below are some possible fixes for the automobile fault code u0156, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u0156, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U0156 Fixing Cost & Complexity
The automobile fault code U0156 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. These factors should be considered when estimating the total cost of diagnosing and fixing the U0156 fault code.
U0156: Understanding The Lost Communication With Instrument Panel Cluster
The U0156 code is a Controller Area Network (CAN) fault code.
CAN is a vehicle bus standard designed to interconnect automotive devices without a host computer. The U0156 code sets when a periodic message from the Information Center Module ‘A’ has not been received.
The Information Center Module ‘A’ is responsible for sending information to the instrument cluster.
The U0156 code indicates that there is a communication problem between the Information Center Module ‘A’ and the instrument cluster. This code can cause the instrument cluster to stop working, and the driver may not be able to see important information such as speed, fuel level, and engine temperature.
FAQ
If the engine light is on and the automobile fault code u0156 is detected, it could be due to a faulty Information Center Module ‘A’, an open or shorted harness, or a poor electrical connection in the circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
When the automobile fault code u0156 is detected, indicating a faulty Information Center Module ‘A’, the engine light or service engine soon warning light may turn on. To fix this issue, one should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.
When the automobile fault code u0156 is detected, the engine light or service engine soon warning light turns on. The possible causes include a faulty Information Center Module ‘A’, an open or shorted Information Center Module ‘A’ harness, or a poor electrical connection in the Information Center Module ‘A’ circuit. To fix this issue, visually inspect the related wiring harness and connectors for any damaged components. Check for broken, bent, pushed out, or corroded connector’s pins.

Wrap Up
If your engine light is on, it could be due to a faulty Information Center Module ‘A’, an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken, bent, or pushed out connector pins.