The automobile fault code U0104 indicates a problem with the Distance Sensing and Cruise Control (DSCC) Module, which can trigger the Engine Light ON or Service Engine Soon Warning Light. The possible causes of this fault code include a faulty DSCC Module, an open or shorted DSCC Module harness, or a poor electrical connection in the DSCC Module circuit.
The importance of repairing this issue lies in the fact that it can affect the vehicle’s cruise control system and distance sensing capabilities. The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins. The repair time is estimated to be around 1.0 hour.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unresponsive Transmission? U0104 Symptoms Explained
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be a sign of u0104 fault code.
Here are the symptoms to look out for:
- The automobile fault code u0104 has the following symptoms: – Engine Light ON (or Service Engine Soon Warning Light) – Loss of communication with the Transmission Control Module (TCM) – Failure of the TCM to communicate with other control modules – Issues with shifting gears – Harsh shifting – Transmission stuck in one gear – Decreased fuel efficiency – Vehicle may not start – Transmission may go into limp mode – Reduced engine power – Transmission may fail to engage or disengage properly.
Decoding U0104: Common Causes Of Fault Code
The automobile fault code u0104 can be caused by various factors, including a faulty DSCC module, open or shorted DSCC module harness, and poor electrical connection in the DSCC module circuit.
- The automobile fault code u0104 can be caused by a faulty Distance Sensing and Cruise Control (DSCC) Module.
- It can also be caused by an open or shorted DSCC Module harness.
- Additionally, a poor electrical connection in the DSCC Module circuit can also trigger this fault code.
Fix U0104 Code: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code u0104, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u0104, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U0104 Repair Cost & Complexity
The automobile fault code U0104 indicates a communication problem between the transmission control module and the engine control module.
The estimated repair time for this fault code is 1.0 hour. The cost of fixing this fault code varies between $75 and $150 per hour, depending on the auto repair shop. Other factors that may influence the cost of fixing this fault code include the severity of the problem, the type of vehicle, and the location of the repair shop.
U0104: Lost Communication With Transmission Control Module
The U0104 code is a Controller Area Network (CAN) communication fault code.
It indicates that the Distance Sensing and Cruise Control Module is not communicating with the vehicle’s computer. This can cause issues with the vehicle’s cruise control and distance sensing systems.
The code is set when the computer does not receive a periodic message from the module. It is important to diagnose and repair this issue to ensure proper functioning of the vehicle’s safety features.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the u0104 fault code. This code is usually caused by a faulty Distance Sensing and Cruise Control (DSCC) Module, an open or shorted DSCC Module harness, or a poor electrical connection in the DSCC Module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a u0104 fault code, it could be caused by a faulty Distance Sensing and Cruise Control (DSCC) Module, an open or shorted DSCC Module harness, or a poor electrical connection in the DSCC Module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.
Ignoring the u0104 fault code can lead to serious consequences such as reduced fuel efficiency, engine misfires, and even engine failure. The fault code is caused by a faulty Distance Sensing and Cruise Control (DSCC) Module, an open or shorted DSCC Module harness, or poor electrical connection. To fix the issue, it is important to visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and the fault code is u0104, it may be due to a faulty Distance Sensing and Cruise Control (DSCC) Module, an open or shorted DSCC Module harness, or poor electrical connection.
Visually inspect the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.
