The P3471 fault code in automobiles indicates a problem with the Cylinder Deactivation Solenoid. The symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause could be low oil pressure, restricted oil passage, engine mechanical condition, faulty Cylinder Deactivation Solenoid, Cylinder Deactivation Solenoid harness is open or shorted, or Cylinder Deactivation Solenoid circuit poor electrical connection. The repair importance is high as it affects the engine’s performance.
The repair difficulty is moderate, and the fix involves visually inspecting the related wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins. The repair time is estimated to be 1.0 hour.
To interpret the fault code, one needs to check the possible causes listed above.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
P3471: Unstable Idling And Stalling – Symptoms Explained
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p3471 fault code. Here are the symptoms to look out for:
- The P3471 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include a decrease in engine power, rough idling, stalling, or hesitation during acceleration.
- Additionally, the vehicle may experience reduced fuel efficiency, and there may be a noticeable decrease in overall performance.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
Decoding P3471: Common Causes Of The Fault Code
The automobile fault code p3471 can be caused by a variety of factors, including low oil pressure and faulty solenoids.
- The automobile fault code P3471 can be caused by low oil pressure, restricted oil passage, engine mechanical condition, faulty Cylinder Deactivation Solenoid, Cylinder Deactivation Solenoid harness being open or shorted, and Cylinder Deactivation Solenoid circuit having poor electrical connection.
Fix Code P3471: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p3471, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p3471, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P3471: Affordable Fix For Complex Automobile Fault Code
The automobile fault code P3471 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of fixing the P3471 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P3471: Your Engine’s Misfire Detection – What You Need To Know
The P3471 code refers to a problem with the cylinder deactivation system in the engine. Specifically, it indicates that there is an issue with the control circuit for the exhaust valve on cylinder 9. This can cause the engine to operate inefficiently and may result in reduced fuel economy.
The cylinder deactivation system is designed to improve fuel economy by deactivating certain cylinders under light load conditions. When the system is working properly, the engine will switch to a V4 mode, deactivating cylinders 1 and 7 on the left bank, and cylinders 4 and 6 on the right bank. However, if there is a problem with the exhaust valve control circuit on cylinder 9, this can cause the system to malfunction and may result in reduced performance and fuel economy.
FAQ
If you see the P3471 fault code on your vehicle, it could be due to low oil pressure, restricted oil passage, engine mechanical condition, faulty cylinder deactivation solenoid, or poor electrical connection in the cylinder deactivation solenoid circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P3471 fault code, start by checking the possible causes listed above. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Cylinder Deactivation Solenoid harness and circuit connections.
Ignoring the P3471 fault code, which indicates a problem with the Cylinder Deactivation Solenoid, can lead to serious consequences such as reduced fuel efficiency, engine damage, and even engine failure. It is important to address the issue promptly by checking the possible causes, visually inspecting the wiring harness and connectors, and looking for damaged components or corroded pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to low oil pressure, restricted oil passage, or a faulty Cylinder Deactivation Solenoid.
Check the possible causes listed above, visually inspect the wiring harness and connectors, and look for damaged components or corroded pins.