[SOLVED] P3005 Code: Fix High Voltage Fuse Snapping

The P3005 automobile fault code indicates a problem with the high voltage fuse or power cable, resulting in the engine light turning on.

It is crucial to address this issue promptly as it can lead to further damage to the vehicle.

The repair process involves visually inspecting the wiring harness and connectors for any damage or corrosion. The difficulty level of this repair is moderate, and it takes approximately 1.0 hour to fix. It is essential to interpret the fault code correctly to identify the root cause of the problem and avoid any further complications.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p3005 fault code.

Here are the symptoms to look out for:

  • The P3005 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include a decrease in engine power, rough idling, stalling, or difficulty starting the engine.
  • Additionally, the vehicle may experience poor fuel economy, reduced acceleration, or misfires.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code p3005 can be caused by a faulty high voltage fuse or power cable.

Read on to discover more possible causes.

  • The automobile fault code p3005 can be caused by a faulty high voltage fuse.
  • It can also be caused by a power cable that is damaged or not properly connected.
  • These are the two main causes of this fault code and should be checked and addressed accordingly.
  • Other potential causes should also be considered and ruled out before attempting any repairs.

Below are the possible fixes for the automobile fault code p3005, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code p3005, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The fault code P3005 is related to the hybrid battery system.

The diagnosis cost may vary depending on the auto repair shop, but it is usually around $100. The estimated repair time for this fault code is 1.0 hour.

The fixing cost will depend on the hourly rate charged by the auto repair shop, which is usually between $75 and $150 per hour.

Therefore, the fixing cost for P3005 can range from $75 to $150.

The P3005 fault code is related to the high voltage system of an automobile. It indicates that a fuse, known as the High Voltage Fuse Sna, has been set in the service plug to protect high-voltage system parts.

However, the voltage of the battery block is less than the specified amount, even though the interlock switch is connected.

This fault code requires immediate attention to prevent any further damage to the high-voltage system.

What are the possible causes of the P3005 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P3005 fault code. This code is caused by a faulty high voltage fuse or power cable. To fix it, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.

How can one visually inspect the related wiring harness and connectors to fix the P3005 fault code?

If you’re experiencing the P3005 fault code, which is indicated by the engine light being on or the service engine soon warning light, it could be caused by a faulty high voltage fuse or power cable. To fix this issue, start by checking the possible causes listed above. Then, visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify the issue and take the necessary steps to fix it.

What are the signs of damaged components and broken, bent, pushed out, or corroded connector’s pins that one should look for when fixing the P3005 fault code?

When fixing the P3005 fault code, one should look for signs of damaged components and broken, bent, pushed out, or corroded connector’s pins. These issues can cause the engine light to turn on or trigger the service engine soon warning light. The cause of this issue could be a faulty high voltage fuse or power cable. To fix this issue, one should visually inspect the related wiring harness and connectors and check for any possible causes.

p3005 error fault code explained

If your engine light is on, it could be due to a faulty high voltage fuse or power cable.

To fix this issue, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector’s pins.

Scroll to Top