The P2808 automobile fault code indicates an issue with the Pressure Control Solenoid ‘G’ valve in the transmission system. Symptoms may include harsh shifting, transmission slippage, and decreased fuel efficiency.
The cause could be a low transmission fluid level, dirty transmission fluid, or a faulty solenoid valve.
Repairing the issue is important to prevent further damage to the transmission system. The difficulty level of the repair is moderate, with a repair time of approximately 1.0 hour. To interpret the fault code, check the possible causes listed above and visually inspect the related wiring harness and connectors.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
P2808: Uncovering Symptoms Of Auto Transmission Fault
Here are some symptoms of the automobile fault code p2808:
- The P2808 fault code is related to the transmission range sensor circuit.
- Symptoms of this fault code include: – Difficulty shifting gears – Harsh shifting – Transmission stuck in one gear – Inability to shift into certain gears – Check Engine Light illuminated – Reduced fuel efficiency – Transmission slipping – Transmission overheating – Transmission failure.
P2808: What Triggers It?
The automobile fault code P2808 can be caused by a range of issues, including low transmission fluid level and faulty pressure control solenoid valve.
- The automobile fault code P2808 can be caused by several factors.
- These include a low transmission fluid level, dirty transmission fluid, a faulty Pressure Control Solenoid ‘G’ valve (Shift Solenoid Valve SL4), an open or shorted Pressure Control Solenoid ‘G’ valve harness, poor electrical connection in the Pressure Control Solenoid ‘G’ valve circuit, a blocked transmission valve body assembly, and a faulty Automatic transaxle assembly.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fix Code P2808: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p2808, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p2808, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2808: Affordable Fix For Your Car’s Transmission
The automobile fault code P2808 refers to a transmission range sensor circuit malfunction.
The estimated repair time for this fault code is 1.0 hour. The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services.
Therefore, the cost of fixing the P2808 fault code can range from $75 to $150, depending on the repair time required.
P2808: Unveiling The Symptoms Of This Auto Fault Code
P2808 is a fault code that indicates a problem with the transmission range sensor circuit. This code is usually accompanied by the illumination of the engine light or service engine soon warning light. The transmission range sensor is responsible for detecting the position of the gear selector and sending this information to the transmission control module.
If the sensor circuit is faulty, it can cause issues with shifting gears, which can lead to poor performance and reduced fuel efficiency.
It is important to have this issue diagnosed and repaired as soon as possible to avoid further damage to the transmission.
FAQ
The P2808 fault code in automobiles can be caused by a low transmission fluid level, dirty transmission fluid, faulty Pressure Control Solenoid ‘G’ valve, open or shorted Pressure Control Solenoid ‘G’ valve harness, poor electrical connection in Pressure Control Solenoid ‘G’ valve circuit, blocked transmission valve body assembly, or a faulty Automatic transaxle assembly. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
To check for faults in the Pressure Control Solenoid ‘G’ valve harness, first, visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. Then, check the possible causes listed above, including low transmission fluid level, dirty transmission fluid, and a faulty Pressure Control Solenoid ‘G’ valve. Finally, ensure that the Pressure Control Solenoid ‘G’ valve circuit has a good electrical connection and that the transmission valve body assembly is not blocked.
To visually inspect the related wiring harness and connectors for the P2808 fault code, first check the possible causes, which include low transmission fluid level, dirty transmission fluid, faulty Pressure Control Solenoid ‘G’ valve, open or shorted Pressure Control Solenoid ‘G’ valve harness, poor electrical connection in the Pressure Control Solenoid ‘G’ valve circuit, blocked transmission valve body assembly, or a faulty Automatic transaxle assembly. Then, inspect the wiring harness and connectors for any damage, broken, bent, pushed out, or corroded pins.

Wrap Up
To fix P2808, check for low or dirty transmission fluid, faulty pressure control solenoid valve, poor electrical connection, or blocked valve body assembly. Visually inspect wiring harness and connectors for damage or corrosion.
Look for broken, bent, or pushed out connector pins.