[SOLVED] P2747 Code: How To Fix Intermediate Shaft Speed Sensor No Signal

The P2747 fault code in automobiles refers to a faulty Intermediate Shaft Speed Sensor ‘B’. This issue is indicated by the illumination of the Engine Light or Service Engine Soon Warning Light. The cause of this problem could be an open or shorted harness of the Intermediate Shaft Speed Sensor ‘B’ or a poor electrical connection in the circuit.

The importance of repairing this issue lies in the fact that it can lead to further damage to the vehicle’s transmission. The repair difficulty is moderate, and it takes approximately 1.0 hour to fix.

To resolve this issue, one should visually inspect the related wiring harness and connectors and check for damaged components.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2747 fault code. Here are the symptoms to look out for:

  • The P2747 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include harsh shifting, transmission slippage, decreased fuel efficiency, and decreased engine performance.
  • Additionally, the vehicle may experience difficulty shifting gears, and the transmission may fail to engage or disengage properly.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code P2747 can be caused by a faulty sensor, open or shorted harness, or poor electrical connection.

  • The automobile fault code P2747 can be caused by a faulty Intermediate Shaft Speed Sensor ‘B’.
  • It can also be caused by an open or shorted harness of the Intermediate Shaft Speed Sensor ‘B’.
  • Additionally, a poor electrical connection in the circuit of the Intermediate Shaft Speed Sensor ‘B’ can also trigger the fault code P2747.

To fix the automobile fault code p2747, check the possible causes and inspect the related wiring harness and connectors for any damage.

  • To fix the automobile fault code P2747, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P2747 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of fixing the P2747 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.

The P2747 code is an OBDII fault code that indicates a problem with the Intermediate Shaft Speed Sensor ‘B’ circuit signal.

The Engine Control Module (ECM) monitors this signal and sets the code when it is out of factory specifications. The Intermediate Shaft Speed Sensor ‘B’ circuit signal is responsible for detecting the shift timing of the gears and controlling the engine torque and hydraulic pressure accordingly.

A malfunction in this circuit can result in rough gear shifts and decreased performance. It is important to have this issue diagnosed and repaired promptly to avoid further damage to the vehicle.

What are the possible causes of the P2747 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P2747 fault code. This code is caused by a faulty intermediate shaft speed sensor ‘B’, an open or shorted harness, or a poor electrical connection in the intermediate shaft speed sensor ‘B’ circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P2747 fault code?

If you’re experiencing the P2747 fault code, start by checking the possible causes listed above. To visually inspect the related wiring harness and connectors, look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Intermediate Shat Speed Sensor ‘B’ harness and circuit poor electrical connection, which could be causing the engine light to turn on.

What are the signs of damaged components that I should look for when fixing the P2747 fault code?

If you’re fixing the P2747 fault code, look out for the engine light or service engine soon warning light turning on. The cause could be a faulty intermediate shaft speed sensor ‘B’, an open or shorted harness, or a poor electrical connection in the circuit. To fix it, visually inspect the wiring harness and connectors, and check for damaged components such as broken, bent, pushed out, or corroded connector pins.

p2747 error fault code explained

If your engine light is on, it may be due to a faulty Intermediate Shaft Speed Sensor ‘B’, an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion.

Check for broken, bent, or pushed out pins.

Scroll to Top