[SOLVED] P2632 Code: Fix Your Fuel Transfer Pump Relay Control Circuit

The automobile fault code P2632 indicates a problem with the secondary fuel pump relay, which can cause the engine light to turn on.

The possible causes of this issue include a faulty relay, an open or shorted harness, poor electrical connection, or a faulty engine control module. To fix the problem, one should visually inspect the wiring harness and connectors for any damage or corrosion.

The repair time for this issue is estimated to be around 1.0.

It is important to address this issue promptly to avoid any further damage to the vehicle. To interpret the fault code, one can use an OBD-II scanner or take the vehicle to a mechanic for diagnosis.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2632 fault code. Here are the symptoms to look out for:

  • The P2632 fault code in an automobile can cause the following symptoms: the engine light or service engine soon warning light will turn on, indicating a problem.
  • The vehicle may experience a decrease in fuel efficiency, leading to more frequent refueling.
  • The engine may also experience a decrease in power, making it difficult to accelerate or maintain speed.
  • The transmission may shift roughly or erratically, causing a jerking sensation while driving.
  • Finally, the vehicle may fail to start or stall while driving, leaving the driver stranded.

The automobile fault code P2632 can be caused by a faulty relay, poor electrical connection, or a faulty ECM.

  • The automobile fault code P2632 can be caused by a faulty secondary fuel pump relay.
  • It can also be caused by an open or shorted secondary fuel pump relay harness.
  • Another cause can be a poor electrical connection in the secondary fuel pump relay circuit.
  • Lastly, a faulty engine control module (ECM) can also trigger this fault code.

To fix the automobile fault code p2632, check the possible causes and inspect related wiring harness and connectors for damage.

  • To fix the automobile fault code p2632, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P2632 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. Therefore, the total cost of diagnosis and fixing the P2632 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.

The P2632 code is related to the fuel transfer pump relay control circuit.

The Engine Control Module (ECM) enables the secondary fuel pump relay when the primary fuel tank is below approximately 50 liters (13.2 gallons). The fuel transfer pump relay applies power to the fuel transfer pump. The control module monitors the voltage on the fuel transfer pump relay control circuit.

If the control module detects an incorrect voltage on the fuel transfer pump relay control circuit, a fuel transfer pump relay control Diagnostic Trouble Code (DTC) sets.

What are the possible causes of the automobile fault code P2632?

If you’re experiencing the engine light ON or Service Engine Soon Warning Light, the possible cause could be a faulty Secondary Fuel Pump Relay, an open or shorted Secondary Fuel Pump Relay harness, a poor electrical connection in the Secondary Fuel Pump Relay circuit, or a faulty Engine Control Module (ECM). To fix this issue, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components and broken, bent, pushed out, or corroded connector’s pins.

How can I fix the P2632 fault code in my car?

If you’re experiencing the P2632 fault code, indicated by the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Secondary Fuel Pump Relay, an open or shorted harness, poor electrical connection, or a faulty Engine Control Module (ECM). To fix it, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or connector pins that are broken, bent, pushed out, or corroded.

What should I visually inspect to troubleshoot the P2632 fault code?

If you’re experiencing the P2632 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This fault code can be caused by a faulty Secondary Fuel Pump Relay, an open or shorted Secondary Fuel Pump Relay harness, a poor electrical connection in the Secondary Fuel Pump Relay circuit, or a faulty Engine Control Module (ECM).

p2632 error fault code explained

If your engine light is on, it could be due to a faulty secondary fuel pump relay, open or shorted harness, poor electrical connection, or a faulty ECM.

Check for these possible causes by visually inspecting the wiring harness and connectors for damage or corrosion.

Scroll to Top