The P2624 fault code in automobiles indicates a problem with the Injector Control Pressure Regulator. The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light. The cause of this fault code could be a faulty Injector Control Pressure Regulator, an open or shorted Injector Control Pressure Regulator harness, or a poor electrical connection in the Injector Control Pressure Regulator circuit.
The repair importance is high as it affects the engine’s performance.
The repair difficulty is moderate, and the repair time is estimated at 1.0 hour. To fix the issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins. It is essential to check the possible causes listed above to interpret the fault code correctly.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2624: Signs Of A Faulty O2 Sensor
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2624 fault code. Here are the symptoms to look out for:
- The P2624 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, rough idling, stalling, and difficulty starting the engine.
- Additionally, the vehicle may experience misfires, hesitation, or surging while driving.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P2624: Common Causes & Fixes
The automobile fault code p2624 can be caused by a faulty regulator, open or shorted harness, or poor electrical connection.
- The automobile fault code P2624 can be caused by a faulty Injector Control Pressure Regulator.
- It can also be caused by an open or shorted Injector Control Pressure Regulator harness.
- Additionally, a poor electrical connection in the Injector Control Pressure Regulator circuit can also trigger this fault code.
Fix Code P2624: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p2624, including inspecting wiring harness and connectors for damage.
- To fix the automobile fault code p2624, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2624: Affordable Fix For Your Car’s Engine
The fault code P2624 indicates a problem with the oxygen sensor circuit in the engine bank 1. The estimated repair time for this fault code is 1.0 hour. The cost of fixing this fault code depends on the hourly rate charged by the auto repair shop.
Most auto repair shops charge between $75 and $150 per hour.
Therefore, the cost of fixing the P2624 fault code can range from $75 to $150.
P2624: Your Car’s Oxygen Sensor Needs Attention
The P2624 code is related to the Injector Control Pressure Regulator (ICPR) Circuit. The Powertrain Control Module (PCM) is responsible for monitoring this circuit.
If the ICPR circuit is not within the factory specifications, the PCM will set the OBDII code.
The P2624 code specifically indicates that the Injector Control Pressure Regulator Circuit is low. This means that the pressure regulator is not functioning properly and is not providing enough pressure to the fuel injectors.
This can cause a variety of issues, including poor engine performance and decreased fuel efficiency.
If you receive the P2624 code, it is important to have your vehicle inspected by a qualified mechanic as soon as possible.
Ignoring this issue can lead to further damage to your vehicle and potentially more expensive repairs down the line.
FAQ
If you see the engine light on or service engine soon warning light, it could be due to the P2624 fault code. This code is usually caused by a faulty injector control pressure regulator, an open or shorted harness, or poor electrical connection in the injector control pressure regulator circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2624 fault code in your automobile, you may notice that the engine light is on or the service engine soon warning light is illuminated. This issue is typically caused by a faulty injector control pressure regulator, an open or shorted harness, or a poor electrical connection in the injector control pressure regulator circuit. To fix the problem, you should visually inspect the related wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the P2624 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you may have a faulty Injector Control Pressure Regulator or an open/shorted harness or poor electrical connection. To identify the cause, visually inspect the related wiring harness and connectors for any damaged components, broken, bent, pushed out, or corroded connector’s pins. Check the “Possible Causes” listed above for further guidance.
Wrap Up
If your engine light is on, it could be due to a faulty Injector Control Pressure Regulator or related wiring issues.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion. Check for broken or bent pins and damaged components.
