The P2622 fault code in automobiles indicates a problem with the Throttle Position SensorSwitch. The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light. The cause of this issue could be a faulty Throttle Position SensorSwitch, an open or shorted Throttle Position SensorSwitch harness, or a poor electrical connection in the Throttle Position SensorSwitch circuit.
The repair importance is high as it affects the engine’s performance. The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins. The repair time is estimated to be 1.0 hour.
It is essential to interpret the fault code to identify the problem accurately and fix it promptly.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 6.67 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
P2622: Signs Of A Faulty O2 Sensor
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2622 fault code.
Here are the symptoms to look out for:
- The P2622 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include a decrease in engine power, reduced fuel efficiency, and rough idling.
- The vehicle may also experience stalling or hesitation during acceleration, and there may be a noticeable decrease in overall performance.
- Additionally, the transmission may shift roughly or erratically, and there may be a burning smell or unusual noises coming from the engine.
Decoding P2622: Common Causes
The automobile fault code p2622 can be caused by a faulty throttle position sensorswitch, an open or shorted harness, or poor electrical connection.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
- The automobile fault code P2622 can be caused by a faulty Throttle Position Sensor/Switch.
- It can also be caused by an open or shorted Throttle Position Sensor/Switch harness.
- Additionally, a poor electrical connection in the Throttle Position Sensor/Switch circuit can also trigger this fault code.
Fix Code P2622: Simple Steps To Get Your Car Running
To fix the automobile fault code p2622, check the possible causes and inspect related wiring harness and connectors for damage.
- To fix the automobile fault code p2622, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2622: Affordable Fix For Complex Automobile Fault Code
The fault code P2622 indicates a problem with the O2 sensor pump current circuit. The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this fault code is influenced by the hourly rate charged by the auto repair shop, which is typically between $75 and $150 per hour. Other factors that may affect the cost include the location of the repair shop, the type of vehicle, and the severity of the problem.
P2622: Your Car’s Oxygen Sensor Needs Attention
The P2622 code is related to the Throttle Position circuit signal.
The Engine Control Module (ECM) monitors this signal.
If the signal is out of factory specifications, the ECM sets the OBDII Code.
The P2622 Code specifically refers to the Throttle Position Output Circuit being high.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P2622 fault code. This code is usually caused by a faulty throttle position sensor/switch, an open or shorted throttle position sensor/switch harness, or a poor electrical connection in the throttle position sensor/switch circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an engine light or service engine soon warning light with a P2622 fault code, it could be due to a faulty throttle position sensor/switch or poor electrical connection. To fix this issue, start by visually inspecting the related wiring harness and connectors. Check for any damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues and get your vehicle back on the road.
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Throttle Position Sensor/Switch or an open or shorted Throttle Position Sensor/Switch harness. The poor electrical connection in the Throttle Position Sensor/Switch circuit can also cause the P2622 fault code. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.

Wrap Up
If your engine light is on, it could be due to a faulty throttle position sensorswitch, an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.
Check the possible causes listed above.