The P2574 fault code in automobiles refers to a faulty Direct Ozone Reduction Catalyst Deterioration Sensor.

The symptom of this issue is the Engine Light ON or Service Engine Soon Warning Light. The cause of this fault code could be a faulty sensor, an open or shorted harness, or a poor electrical connection.

The repair importance of this issue is moderate, and the difficulty level is low.

To fix this issue, one needs to visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins. The repair time for this issue is approximately 1.0 hour.

It is essential to interpret the fault code correctly to identify the root cause of the problem.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2574 fault code. Here are the symptoms to look out for:

  • The P2574 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include reduced engine power, decreased fuel efficiency, and rough idling.
  • Additionally, the vehicle may experience stalling or hesitation during acceleration, and there may be a noticeable decrease in overall performance.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe operation on the road.

The P2574 fault code can be caused by a faulty sensor, open or shorted harness, or poor electrical connection.

  • The automobile fault code P2574 can be caused by a faulty Direct Ozone Reduction Catalyst Deterioration Sensor.
  • It can also be caused by an open or shorted Direct Ozone Reduction Catalyst Deterioration Sensor harness.
  • Additionally, a poor electrical connection in the Direct Ozone Reduction Catalyst Deterioration Sensor circuit can also trigger this fault code.

Below are the possible fixes for the automobile fault code p2574, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code P2574, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P2574 can be diagnosed and fixed within an estimated repair time of 1.0 hour.

The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of fixing the P2574 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.

The P2574 code is related to the Direct Ozone Reduction Catalyst Deterioration Sensor.

The Engine Control Module (ECM) monitors this sensor’s signal. If the signal is out of factory specifications, the ECM sets the OBDII code.

The P2574 code specifically indicates that the Direct Ozone Reduction Catalyst Deterioration Sensor Circuit is low.

This means that the sensor is not detecting the proper levels of ozone reduction catalyst deterioration.

It is important to address this issue promptly to ensure proper functioning of the vehicle’s emissions system.

What are the possible causes of the P2574 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P2574 fault code. This code is caused by a faulty Direct Ozone Reduction Catalyst Deterioration Sensor, an open or shorted harness, or a poor electrical connection in the sensor circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P2574 fault code?

To fix the P2574 fault code, start by checking the “Possible Causes” listed above. Then, visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Direct Ozone Reduction Catalyst Deterioration Sensor harness and circuit connections.

What are the symptoms of a faulty Direct Ozone Reduction Catalyst Deterioration Sensor that triggers the P2574 fault code?

If the Direct Ozone Reduction Catalyst Deterioration Sensor is faulty, the engine light will turn on, triggering the P2574 fault code. This can be caused by an open or shorted harness, or a poor electrical connection in the sensor circuit. To fix the issue, inspect the wiring harness and connectors for any damage or corrosion, and check for broken or bent pins.

p2574 error fault code explained

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Direct Ozone Reduction Catalyst Deterioration Sensor, open or shorted harness, or poor electrical connection.

Check the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.

Scroll to Top