The P2537 fault code in automobiles indicates a problem with the Body Control Module (BCM). The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light.

The cause of this fault code could be a faulty BCM, an open or shorted BCM harness, or a poor electrical connection in the BCM circuit. The importance of repairing this issue lies in the fact that the BCM controls various functions in the vehicle, including the power windows, door locks, and lighting. The difficulty level of repairing this issue is moderate, with a repair time of 1.0.

To fix this issue, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2537 fault code. Here are the symptoms to look out for:

  • The P2537 fault code in an automobile can cause several symptoms.
  • The most common symptom is the illumination of the engine light or service engine soon warning light.
  • Other symptoms include issues with the vehicle’s transmission, such as difficulty shifting gears or the transmission slipping.
  • The vehicle may also experience a decrease in fuel efficiency, and the engine may stall or hesitate during acceleration.
  • Additionally, the vehicle may experience a loss of power or have difficulty starting.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

P2537 fault code can be caused by a faulty BCM, open or shorted harness, or poor electrical connection.

  • The automobile fault code P2537 can be caused by a faulty Body Control Module (BCM).
  • It can also be caused by an open or shorted Body Control Module harness.
  • Additionally, a poor electrical connection in the Body Control Module circuit can also trigger this fault code.

Below are the possible fixes for the automobile fault code p2537, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code p2537, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P2537 can be diagnosed and fixed within an estimated repair time of 1.0 hour.

The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.

Therefore, the total cost of fixing the P2537 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.

The P2537 code is related to the Ignition Accessory Switch Circuit. The control module monitors the voltage on the Ignition AccessoryRun circuit from the BCM.

If the voltage is less than 6V for 1 minute, the control module will set the Diagnostic Trouble Code (DTC) P2537.

This code indicates that there is a low voltage issue with the Ignition Accessory Switch Circuit.

What are the possible causes of the automobile fault code P2537 that triggers the engine light or service engine soon warning light?

If you see the engine light or service engine soon warning light with the fault code P2537, it could be due to a faulty Body Control Module (BCM), an open or shorted BCM harness, or poor electrical connection in the BCM circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can you fix the P2537 fault code in your automobile, and what steps should you take to ensure that the issue is resolved?

If you’re experiencing the P2537 fault code in your automobile, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Body Control Module (BCM), an open or shorted BCM harness, or a poor electrical connection in the BCM circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

What are the signs that your automobile’s Body Control Module (BCM) is faulty, and how can you prevent this issue from occurring in the future?

If your engine light is on, it could be a sign of a faulty Body Control Module (BCM). This can be caused by an open or shorted BCM harness or poor electrical connection. To prevent this issue, regularly inspect the wiring harness and connectors for any damage or corrosion. If you suspect a faulty BCM, visually inspect the related components and connectors for any issues.

p2537 error fault code explained

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Body Control Module (BCM), an open or shorted BCM harness, or poor electrical connection.

Check the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.

Scroll to Top