The P24B5 automobile fault code indicates a problem with the Exhaust Particulate Matter Sensor, which can trigger the Engine Light or Service Engine Soon Warning Light. The cause of this issue could be a faulty sensor, an open or shorted harness, or a poor electrical connection.
It is important to visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this issue is estimated to be around 1.0. To interpret the fault code, it is recommended to check the “Possible Causes” listed above and follow the suggested fix accordingly.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P24B5: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p24b5 fault code.
Here are the symptoms to look out for:
- The P24B5 fault code in an automobile can cause several symptoms.
- The most common symptom is the illumination of the engine light or service engine soon warning light.
- Other symptoms include reduced engine power, decreased fuel efficiency, rough idling, and difficulty starting the engine.
- Additionally, the vehicle may emit black smoke from the exhaust, and there may be a noticeable decrease in acceleration.
- If you experience any of these symptoms, it is important to have your vehicle diagnosed and repaired by a qualified mechanic as soon as possible.
Decoding P24B5: Common Causes
The P24B5 fault code can be caused by a faulty sensor, open or shorted harness, or poor electrical connection.
- The automobile fault code P24B5 can be caused by a faulty exhaust particulate matter sensor.
- It can also be caused by an open or shorted exhaust particulate matter sensor harness.
- Additionally, a poor electrical connection in the exhaust particulate matter sensor circuit can also trigger this fault code.
Fix Code P24B5: Simple Steps To Get Back On Road
To fix the p24b5 automobile fault code, check the possible causes and inspect related components for damage or corrosion.
- To fix the automobile fault code p24b5, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P24B5: Affordable Fix For Your Car
The fault code P24B5 indicates an issue with the exhaust gas temperature sensor circuit. The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.
Other factors that may influence the cost include the location of the repair shop, the type of vehicle, and the severity of the issue.
P24B5: Your Car’s Exhaust System Needs Attention
The P24B5 fault code is related to the Particulate Matter (PM) sensor in diesel engines.
The PM sensor monitors the amount of soot in the diesel exhaust gas. The sensor has a ceramic element with comb-shaped Interdigital Electrodes (IDE), a heater, and a positive temperature coefficient resistor for temperature measurement.
The sensor performs a regeneration to clean off soot before the measurement phase begins. The P24B5 code is set when the sensor control unit detects an internal fault of the sensor, fault of the sensor circuitry, or low voltage on the sensor supply circuit.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P24B5 fault code. This code is usually caused by a faulty exhaust particulate matter sensor, an open or shorted sensor harness, or a poor electrical connection in the sensor circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P24B5 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you may have a faulty Exhaust Particulate Matter Sensor, an open or shorted harness, or a poor electrical connection. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues and determine the best course of action to resolve the problem.
Ignoring the P24B5 fault code, caused by a faulty exhaust particulate matter sensor, can lead to serious consequences. The engine light will remain on, indicating a problem, and the vehicle may fail an emissions test. Additionally, the faulty sensor can cause damage to the engine and exhaust system, resulting in costly repairs. It is important to address the issue promptly by visually inspecting the wiring harness and connectors and checking for damaged components.
Wrap Up
If your engine light is on, it could be due to a faulty Exhaust Particulate Matter Sensor, an open or shorted harness, or poor electrical connection.
Check the wiring harness and connectors for damage, broken or corroded pins.
