The P247F automobile fault code indicates a problem with the Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 4. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code can be a faulty EGTS, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. The importance of repairing this issue lies in the fact that it can lead to decreased engine performance and increased emissions. The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 6.67 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P247F: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p247f fault code. Here are the symptoms to look out for:
- The P247F fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
P247F: Uncovering The Culprits Behind The Fault Code
The automobile fault code P247F can be caused by a range of issues, including faulty sensors, electrical problems, exhaust leaks, and particulate buildup.
- The automobile fault code P247F can be caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 4.
- It can also be caused by an open or shorted Exhaust Gas Temperature Sensor Bank 2 Sensor 4 harness.
- A poor electrical connection in the Exhaust Gas Temperature Sensor Bank 2 Sensor 4 circuit can also trigger this fault code.
- Additionally, exhaust leaks and excessive particulate matter buildup on the sensor can cause the P247F fault code.
Fix P247F: Your Guide To Resolving The Issue
To fix the automobile fault code p247f, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p247f, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P247F: Affordable Fix For Complex Auto Fault Code
The automobile fault code P247F can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. Therefore, the total cost of diagnosis and fixing the P247F fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time.
P247F: The Low-Temperature Exhaust Gas Recirculation System
The P247F code is related to the Exhaust Gas Temperature Sensor (EGTS). The EGTS detects exhaust gas temperature and converts it into a voltage. The PCM monitors the EGTS for proper circuit continuity and out of range high values.
The code is set when the EGTS is out of factory specifications.
It is specifically related to Bank 2 S.
FAQ
If you notice the engine light on or service engine soon warning light, it could be due to the P247F fault code. This code is usually caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 4, an open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light with a P247F fault code, it could be due to a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 4, an open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix it, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the P247F fault code. This code is caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 4, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 4, exhaust leaks, or excessive particulate matter buildup on the sensor.
Check the wiring harness and connectors for damage and inspect the components for any issues.
