The P247E automobile fault code indicates a problem with the Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light. The cause of this fault code can be a faulty EGTS, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor.
The importance of repairing this issue lies in the fact that it can affect the vehicle’s performance and fuel efficiency.
The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins. The repair time is estimated to be around 1.0 hour. To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related components.
| Repair Importance Level | 6.67 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P247E: Uncovering The Symptoms Of This Auto Fault Code
If you notice the engine light on or service engine soon warning light, it could be a sign of the p247e fault code. Here are some symptoms to look out for:
- The P247E fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty shifting gears.
- Additionally, the vehicle may experience a loss of acceleration or stalling while driving.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P247E: Common Causes Of The Fault Code
The automobile fault code P247E can be caused by various factors, including a faulty EGTS, open or shorted harness, poor electrical connection, exhaust leaks, and particulate matter buildup.
- The automobile fault code P247E can be caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3.
- It can also be caused by an open or shorted Exhaust Gas Temperature Sensor Bank 2 Sensor 3 harness.
- Poor electrical connection in the Exhaust Gas Temperature Sensor Bank 2 Sensor 3 circuit can also trigger this fault code.
- Additionally, exhaust leaks and excessive particulate matter buildup on the sensor can cause the P247E fault code.
Fix P247E: Your Guide To Resolving The Fault Code
To fix the p247e automobile fault code, check the possible causes and inspect related wiring harness and connectors for damage.
- To fix the automobile fault code p247e, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P247E: Affordable Fix For Complex Auto Fault Code
The automobile fault code P247E can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of fixing the P247E fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P247E: Your Car’s Diesel Particulate Filter Needs Attention
The P247E code is related to the Exhaust Gas Temperature Sensor (EGTS).
The EGTS detects exhaust gas temperature and converts it into a voltage. The PCM sets the P247E code when the EGTS is out of factory specifications. The code specifically indicates that the exhaust gas temperature is out of range for Bank 2 Sensor 3.
This fault code can cause increased emissions and reduced engine performance. It is important to have the EGTS checked and replaced if necessary to ensure proper engine function and emissions control.
FAQ
If you see the engine light on or service engine soon warning light, it could be due to the P247E fault code. This code is usually caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, an open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON (or Service Engine Soon Warning Light) due to the P247E fault code, you may have a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, an open or shorted harness, a poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, check the “Possible Causes” listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Ignoring the P247E fault code, which indicates a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, can lead to serious consequences. The engine light will remain on, indicating a problem, and the vehicle may experience reduced performance and fuel efficiency. Ignoring the issue can also lead to further damage to the engine and exhaust system, resulting in costly repairs. It is important to check the possible causes and visually inspect the related wiring harness and connectors to avoid these consequences.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup.
Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.
