The P247A automobile fault code indicates a problem with the Exhaust Gas Temperature Sensor (EGTS) Bank 1 Sensor 3. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code can be a faulty EGTS, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor.
The importance of repairing this issue lies in the fact that it can affect the vehicle’s performance and fuel efficiency.
The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins. The repair time is estimated to be around 1.0 hour. To interpret the fault code, one needs to use an OBD-II scanner or code reader.
| Repair Importance Level | 6.67 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P247A: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p247a fault code. Here are the symptoms to look out for:
- The P247A fault code in automobiles can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light, decreased fuel efficiency, engine misfires, rough idling, difficulty starting the engine, reduced power output, and increased emissions.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure optimal performance.
Decoding P247A: Unveiling The Causes
The automobile fault code P247A can be caused by a range of issues, including faulty sensors, electrical problems, exhaust leaks, and particulate buildup.
- The automobile fault code P247A can be caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 1 Sensor 3.
- It can also be caused by an open or shorted Exhaust Gas Temperature Sensor Bank 1 Sensor 3 harness.
- Poor electrical connection in the Exhaust Gas Temperature Sensor Bank 1 Sensor 3 circuit can also trigger this fault code.
- Additionally, exhaust leaks and excessive particulate matter buildup on the sensor can cause the P247A fault code.
Fix Code P247A: Simple Steps To Get Your Car Running
To fix the automobile fault code p247a, check the possible causes and inspect related components for damage or corrosion.
- To fix the automobile fault code p247a, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P247A: Affordable Fix For Complex Auto Fault Code
The fault code P247A is related to the exhaust gas temperature sensor circuit.
The estimated repair time for this fault code is 1.0 hour. The cost of fixing this fault code is dependent on the hourly rate charged by the auto repair shop.
The average hourly rate charged by most auto repair shops is between $75 and $150. Therefore, the cost of fixing the P247A fault code can range from $75 to $150.
P247A: Your Car’s Exhaust System Needs Attention
The P247A code is related to the Exhaust Gas Temperature Sensor (EGTS) in a vehicle’s Powertrain Control Module (PCM).
The EGTS is responsible for detecting exhaust gas temperature and converting it into a voltage signal that is sent back to the PCM. If the EGTS is out of factory specifications, the PCM will set the P247A OBDII code, indicating that the exhaust gas temperature is out of range for Bank 1 Sensor 3.
FAQ
If you see the engine light on or service engine soon warning light, it could be due to the P247A fault code. This code is usually caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 1 Sensor 3, an open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P247A fault code in your automobile, which is indicated by the engine light being on, it could be due to a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 1 Sensor 3, an open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you see the Engine Light ON or Service Engine Soon Warning Light in your automobile, it could be due to the P247A fault code. This code is caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 1 Sensor 3, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and the fault code is p247a, it could be due to a faulty exhaust gas temperature sensor or related wiring issues.
Check for damaged components and inspect the wiring harness and connectors for any issues.
