If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the P2467 fault code. This code indicates a problem with the Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3. The possible causes include a faulty sensor, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor.
The repair importance is high as it can affect the engine’s performance and fuel efficiency.
The repair difficulty is moderate, and it takes around 1.0 hour to fix.
To interpret the fault code, you need to check the possible causes listed above and visually inspect the related wiring harness and connectors.
| Repair Importance Level | 6.67 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
Uncovering The Symptoms Of P2467 Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2467 fault code.
Here are the symptoms to look out for:
- The P2467 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience increased emissions, a decrease in acceleration, and a rough idle.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
P2467: Uncovering The Culprits Behind The Fault Code
There are several causes of the automobile fault code P2467, including a faulty EGTS and exhaust leaks.
- The automobile fault code P2467 can be caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3.
- It can also be caused by an open or shorted Exhaust Gas Temperature Sensor Bank 2 Sensor 3 harness.
- A poor electrical connection in the Exhaust Gas Temperature Sensor Bank 2 Sensor 3 circuit can also trigger this fault code.
- Additionally, exhaust leaks and excessive particulate matter buildup on the sensor can cause the P2467 fault code.
Fix Code P2467: Simple Steps To Get Your Car Running
To fix the automobile fault code p2467, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2467, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2467: Affordable Fix For Your Car’s Exhaust System
The fault code P2467 indicates a problem with the diesel particulate filter pressure sensor circuit. The estimated repair time for this issue is 1.0 hour. The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.
Other factors that may influence the cost include the location of the repair shop, the severity of the issue, and the type of vehicle.
P2467: Your Diesel Particulate Filter Needs Urgent Attention
The P2467 code is related to the Exhaust Gas Temperature Sensor (EGTS).
The EGTS is responsible for detecting exhaust gas temperature and converting it into a voltage signal.
The PCM monitors the EGTS for proper circuit continuity and out of range high values.
If the EGTS is out of factory specifications, the PCM sets the P2467 OBDII code.
This code specifically refers to the circuit rangeperformance of Bank 2 Sensor 3.
FAQ
If you see the engine light on or service engine soon warning light, it could be due to the P2467 fault code. This code is caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, an open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or corroded connector pins.
If you’re experiencing the P2467 fault code, which is indicated by the engine light being on, you may have a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, an open or shorted harness, a poor electrical connection, exhaust leaks, or excessive particulate matter buildup on the sensor. To fix this issue, check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.
Ignoring the P2467 fault code, caused by a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, can lead to serious consequences. The engine light will remain on, indicating a problem, and the vehicle may experience reduced performance and fuel efficiency. Ignoring the issue can also cause damage to other engine components and lead to costly repairs. It is important to check the possible causes, visually inspect the wiring harness and connectors, and look for damaged components to fix the issue promptly.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Exhaust Gas Temperature Sensor (EGTS) Bank 2 Sensor 3, open or shorted harness, poor electrical connection, exhaust leaks, or excessive particulate matter buildup.
Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.
