If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the P244A fault code. This code indicates a problem with the diesel particulate filter, which could be faulty or have leaks in the pressure sensor connecting hose.

Aftermarket accessories and performance modifications can also cause this issue. It’s important to visually inspect the wiring harness and connectors for any damage or corrosion.

The repair time for this fault code is 1.0, and it’s crucial to fix it to avoid further damage to the engine.

To interpret the fault code, check the possible causes listed above.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p244a fault code.

Here are the symptoms to look out for:

  • The P244A fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include reduced engine power, engine misfires, rough idling, decreased fuel efficiency, and unusual noises coming from the engine.
  • Additionally, the vehicle may experience difficulty starting or may stall while driving.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code p244a can be caused by a range of factors, including a faulty diesel particulate filter and exhaust leaks.

  • The automobile fault code P244A can be caused by a faulty diesel particulate filter.
  • It can also be caused by exhaust leaks before or near the diesel particulate filter pressure sensor.
  • Leaks in the diesel particulate filter pressure sensor connecting hose can also trigger this fault code.
  • Lastly, aftermarket accessories and performance modifications can also cause the P244A fault code to appear.

To fix the p244a automobile fault code, check the possible causes and inspect related components for damage or corrosion.

  • To fix the automobile fault code p244a, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors.
  • Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
  • Ensure that everything is in good condition.
  • The estimated repair time for this fix is 1.0 hour.

The automobile fault code P244A is related to the secondary air injection system. The diagnosis cost may vary depending on the auto repair shop, but it usually ranges from $50 to $150. The estimated repair time for this fault code is 1.0 hour.

The fixing cost will depend on the hourly rate charged by the auto repair shop, which is usually between $75 and $150 per hour. Other factors that may influence the fixing cost include the severity of the problem, the type of vehicle, and the location of the auto repair shop.

The P244A fault code is related to the aftertreatment Diesel Particulate Filter. The Engine Control Module (ECM) uses the Exhaust Pressure Sensor to monitor the pressure differential through the aftertreatment Diesel Particulate Filter.

If the ECM detects that the aftertreatment diesel particulate filter is not present in the aftertreatmentexhaust system, it will set the fault. This DTC is a two trip fault and active regeneration of the aftertreatment Diesel Particulate Filter will be disabled. The MIL lamp will turn off immediately after the diagnostic runs and passes.

What are the possible causes of the P244A fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P244A fault code. This code is often caused by a faulty diesel particulate filter, exhaust leaks before or near the diesel particulate filter pressure sensor, leaks in the diesel particulate filter pressure sensor connecting hose, or aftermarket accessories and performance modifications. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components and broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P244A fault code?

If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a P244A fault code, there are a few possible causes to consider. These include a faulty diesel particulate filter, exhaust leaks before or near the diesel particulate filter pressure sensor, leaks in the diesel particulate filter pressure sensor connecting hose, or aftermarket accessories and performance modifications. To fix the issue, start by visually inspecting the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.

Can aftermarket accessories and performance modifications cause the P244A fault code?

Yes, aftermarket accessories and performance modifications can cause the P244A fault code. This fault code is indicated by the engine light being on or the service engine soon warning light. The cause of this fault code can be a faulty diesel particulate filter, exhaust leaks before or near the diesel particulate filter pressure sensor, leaks in the diesel particulate filter pressure sensor connecting hose, or aftermarket accessories and performance modifications. To fix this issue, one should check the possible causes listed above and visually inspect the related wiring harness and connectors for any damage or corrosion.

p244a error fault code explained

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty diesel particulate filter, exhaust leaks, or aftermarket accessories. Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.

Scroll to Top