The P2419 automobile fault code indicates a problem with the Canister Pump Module, which can cause the Engine Light to turn on. The possible causes of this issue include a faulty Canister Pump Module, an open or shorted Canister Pump Module harness, poor electrical connection in the Canister Pump Module circuit, or a faulty Engine Control Module (ECM).
The importance of repairing this issue lies in the fact that it can affect the performance of the vehicle. The repair difficulty is moderate, and it takes approximately 1.0 hour to fix.
To interpret the fault code, one should check the possible causes listed above and visually inspect the related wiring harness and connectors for any damage or corrosion.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2419: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2419 fault code.
Here are the symptoms to look out for:
- The P2419 fault code in an automobile can cause several symptoms.
- The most common symptom is the illumination of the engine light or service engine soon warning light.
- Other symptoms include a decrease in engine performance, reduced fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration power.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2419: Uncovering The Culprits Behind The Code
The automobile fault code P2419 can be caused by a faulty canister pump module, open or shorted harness, poor electrical connection, or a faulty engine control module.
- The automobile fault code P2419 can be caused by a faulty Canister Pump Module.
- It can also be caused by an open or shorted Canister Pump Module harness.
- Another cause can be a poor electrical connection in the Canister Pump Module circuit.
- Lastly, a faulty Engine Control Module (ECM) can also trigger this fault code.
Fix Code P2419: Quick Solutions For Your Automobile
Below are the possible fixes for the automobile fault code p2419, including inspecting wiring harness and connectors for damage.
- To fix the automobile fault code P2419, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2419: Affordable Fix For Complex Automobiles
The automobile fault code P2419 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of diagnosis and fixing the P2419 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
P2419: Your Car’s Fuel System Needs Attention
The P2419 code is related to the Evaporative Emission (EVAP) system.
The Engine Control Module (ECM) monitors for leaks and actuator malfunctions based on the EVAP pressure. The leak detection pump creates negative pressure through the reference orifice.
If the EVAP pressure is not between 97 to 100 kPa(abs) within a minute, the ECM interprets this as a malfunction.
The ECM illuminates the MIL and stores a Diagnostic Trouble Code (DTC) if this malfunction is detected in consecutive drive cycles.
The P2419 code specifically refers to a low circuit in the Evaporative Emission System Switching Valve Control.
The Canister Pump Module is attached to the EVAP Canister and contains the Canister Pressure Sensor, the Leak Detection Pump, and the Vent Valve.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P2419 fault code. This code is usually caused by a faulty canister pump module, an open or shorted canister pump module harness, a poor electrical connection in the canister pump module circuit, or a faulty engine control module (ECM). To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2419 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, there are a few things you can do to fix it. The cause of this issue could be a faulty Canister Pump Module, an open or shorted Canister Pump Module harness, a poor electrical connection in the Canister Pump Module circuit, or a faulty Engine Control Module (ECM). To address this problem, you should visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
While a faulty Engine Control Module (ECM) is listed as a possible cause of the P2419 fault code, it is not a common cause. The most common cause of this fault code is a faulty Canister Pump Module or issues with its wiring harness and electrical connections. To fix the issue, it is recommended to visually inspect the related wiring harness and connectors, checking for any damaged components or broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on, it could be due to a faulty Canister Pump Module, open or shorted harness, poor electrical connection, or a faulty Engine Control Module. Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken, bent, or pushed out pins.
