The P2414 automobile fault code indicates a problem with the Oxygen (O2) Sensor or its related circuitry. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code could be a faulty Oxygen (O2) Sensor, an open or shorted Oxygen (O2) harness, or a poor electrical connection in the Oxygen (O2) circuit.
The repair importance is high as it can affect the vehicle’s performance and fuel efficiency. The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors for any damage or corrosion.
The fault code can be interpreted using an OBD-II scanner.
| Repair Importance Level | 6.67 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P2414: Signs Of A Faulty Exhaust Gas Recirculation (Egr) System
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2414 fault code.
Here are the symptoms to look out for:
- The P2414 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and rough idling.
- Additionally, the vehicle may experience difficulty starting or stalling while driving.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
P2414: Uncovering The Culprits Behind The Code
The automobile fault code p2414 can be caused by a faulty oxygen sensor, open or shorted oxygen harness, or poor electrical connection.
- The automobile fault code P2414 can be caused by a faulty Oxygen (O2) sensor.
- It can also be caused by an open or shorted Oxygen (O2) harness.
- Additionally, a poor electrical connection in the Oxygen (O2) circuit can also trigger this fault code.
Fix Code P2414: Quick Steps To Get Your Car Running
To fix the p2414 automobile fault code, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2414, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2414: Affordable Fix For Complex Automobiles
The fault code P2414 indicates an issue with the exhaust gas recirculation (EGR) system.
The diagnosis and fixing cost of this fault code is influenced by the estimated repair time, which is 1.0 hour. The cost of repair is also affected by the hourly rate charged by the auto repair shop, which is typically between $75 and $150 per hour. These factors should be considered when estimating the total cost of diagnosing and fixing the P2414 fault code.
P2414: Your Car’s Exhaust System Needs Attention
The P2414 code is related to the Oxygen (O2) Sensor performance in an automobile. The Engine Control Module (ECM) monitors the O2 Sensor signal and sets the OBDII code when it is out of factory specifications. The P2414 code specifically refers to an O2 Sensor Exhaust Sample Error in Bank 1 S.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P2414 fault code. This code is usually caused by a faulty oxygen (O2) sensor, an open or shorted oxygen (O2) harness, or a poor electrical connection in the oxygen (O2) circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2414 fault code, which is indicated by the engine light or service engine soon warning light being on, there are a few things you can do to fix it. One possible cause is a faulty oxygen (O2) sensor, but it could also be due to an open or shorted O2 harness or poor electrical connection in the O2 circuit. To address these issues, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
If you’re fixing the P2414 fault code, keep an eye out for the engine light being on or the service engine soon warning light. The cause of this issue could be a faulty oxygen (O2) sensor, an open or shorted oxygen (O2) harness, or a poor electrical connection in the oxygen (O2) circuit. To fix this problem, check the possible causes listed above and visually inspect the related wiring harness and connectors. Be sure to look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty oxygen sensor, open or shorted oxygen harness, or poor electrical connection. Check the wiring harness and connectors for damage, broken or corroded pins.
Inspect the components listed under “Possible Causes” to fix the issue.
