If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the P2336 fault code. This code indicates a possible lack or loss of power in your automobile. The cause of this issue could be a faulty knock sensor, poor electrical connection in the knock sensor circuit, an open or shorted knock sensor harness, or a faulty Engine Control Module (ECM).
The repair time for this issue is around 1.0, and it is important to visually inspect the related wiring harness and connectors to check for damaged components and broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2336: Unstable Engine Idling – Symptoms & Solutions
If you’re experiencing the engine light turning on or a possible lack of power, you may be dealing with the p2336 fault code.
- The P2336 fault code in an automobile can cause the following symptoms: the engine light will turn on or the service engine soon warning light will appear.
- There may be a possible lack or loss of power in the vehicle.
- These are the only known symptoms associated with this particular fault code.
- It is important to address these symptoms as soon as possible to prevent further damage to the vehicle.
P2336: Uncovering The Culprits Behind The Fault Code
P2336 fault code can be caused by a faulty knock sensor, poor electrical connection, open or shorted harness, or a faulty ECM.
- The automobile fault code P2336 can be caused by a faulty knock sensor.
- It can also be caused by a knock sensor circuit with poor electrical connection.
- Another cause is a knock sensor harness that is open or shorted.
- Lastly, a faulty Engine Control Module (ECM) can also trigger this fault code.
Fix Code P2336: Simple Steps To Get Your Car Running
To fix the p2336 automobile fault code, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2336, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2336: Affordable Fix For Your Car’s Ignition System
The fault code P2336 indicates a problem with the ignition coil K primary control circuit. The diagnosis involves checking the wiring and connections of the ignition coil and the powertrain control module.
The estimated repair time for this fault code is 1.0 hour.
The fixing cost will depend on the hourly rate charged by the auto repair shop, which is typically between $75 and $150 per hour.
Other factors that may affect the cost include the location of the repair shop, the type of vehicle, and the availability of replacement parts.
P2336: Ignition Coil ‘b’ Primary Control Circuit Low – Explained
P2336 is a fault code that indicates a problem with the Knock Sensor (KS) in Cylinder 1. The KS senses engine knocking using a piezoelectric element and is attached to the cylinder block, cylinder head or intake manifold.
When a knocking vibration from the cylinder block is sensed as vibrational pressure, it is converted into a voltage signal and sent to the Engine Control Module (ECM). The ECM uses this signal to retard the ignition timing and protect the engine from damaging pre-ignition.
FAQ
If you’re experiencing a lack or loss of power and the engine light is on, the P2336 fault code may be the culprit. This code is often caused by a faulty knock sensor, poor electrical connection in the knock sensor circuit, an open or shorted knock sensor harness, or a faulty Engine Control Module (ECM). To fix the issue, it’s important to visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.
If the engine light is on and there is a possible lack or loss of power, it could be due to a faulty knock sensor or a poor electrical connection in the knock sensor circuit. To fix this issue, check the wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector pins. Also, inspect the knock sensor harness for any open or shorted circuits. Finally, check the Engine Control Module (ECM) for any faults.
To visually inspect the related wiring harness and connectors for the P2336 fault code, check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. Also, check the “Possible Causes” listed above and inspect the knock sensor circuit for poor electrical connection or an open or shorted harness. Finally, check the Engine Control Module (ECM) for any faults.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty knock sensor, poor electrical connection, open or shorted knock sensor harness, or a faulty Engine Control Module (ECM). Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.
