The P2317 fault code in automobiles indicates a problem with the ignition coil ‘F’ circuit.
This can cause the engine light to turn on and the engine to run rough. The cause of this issue could be a faulty ignition coil ‘F’, an open or shorted harness, or a poor electrical connection.
It is important to visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this issue is estimated to be around 1.0.
To interpret the fault code, one should check the possible causes listed above and look for any broken or bent connector pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2317: Unstable Engine, Misfiring & Stalling – Symptoms Explained
If you’re experiencing an illuminated Engine Light and rough engine performance, read on to learn more about the symptoms of the p2317 automobile fault code.
- The P2317 fault code in an automobile can cause the following symptoms: the engine light will turn on or the service engine soon warning light will appear.
- The engine may start running rough, and there may be a noticeable decrease in engine performance.
- The vehicle may also experience misfires, stalling, or hesitation during acceleration.
- Additionally, the engine may produce unusual noises or vibrations, and there may be a decrease in fuel efficiency.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2317: Ignition Coil Circuit Failure – Causes Explained
P2317 fault code can be caused by a faulty ignition coil, open or shorted harness, or poor electrical connection.
- The automobile fault code P2317 can be caused by a faulty ignition coil ‘F’.
- It can also be caused by an open or shorted ignition coil ‘F’ harness.
- Additionally, a poor electrical connection in the ignition coil ‘F’ circuit can also trigger this fault code.
Fix Code P2317: Simple Steps To Get Your Car Running
To fix the p2317 fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2317, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- Ensure that all the connections are secure and free from corrosion.
- This repair should take approximately 1.0 hour.
P2317: Affordable Fix For Your Car’s Ignition System
The fault code P2317 indicates an issue with the ignition coil F secondary circuit. The diagnosis process involves checking the wiring and connections, testing the ignition coil, and inspecting the spark plugs.
The estimated repair time for this fault code is 1.0 hour.
The fixing cost will depend on the hourly rate of the auto repair shop, which typically ranges between $75 and $150 per hour. Other factors that may affect the cost include the severity of the issue and the need for replacement parts.
P2317: Ignition Coil F Secondary Circuit – What You Need To Know
The P2317 code is related to the ignition coil in the automobile.
The Powertrain Control Module controls the current flow through the primary ignition coil. The PCM provides a switched ground path through the ignition coil driver to ground.
The P2317 code sets when the PCM detects a short to voltage in the circuit. The code indicates a problem with the ignition coil ‘F’ secondary circuit.
The PCM continuously monitors the ignition system for concerns.
The magnetic field collapse induces a secondary high voltage surge and the spark plug is fired.
The PCM uses the flyback voltage as feedback during the ignition diagnostics.
FAQ
The P2317 fault code in automobiles is indicated by the engine light turning on and the engine running rough. The possible causes of this fault code include a faulty ignition coil ‘F’, an open or shorted ignition coil ‘F’ harness, or a poor electrical connection in the ignition coil ‘F’ circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
To fix the P2317 fault code, start by checking the possible causes listed above. Visually inspect the related wiring harness and connectors for any damage or corrosion. Look for broken, bent, or pushed out connector pins. This can help identify if the issue is caused by a faulty ignition coil ‘F’, an open or shorted harness, or a poor electrical connection in the ignition coil circuit.
The P2317 fault code is indicated by the Engine Light ON or Service Engine Soon Warning Light and the engine running rough. The cause of this fault code is a faulty Ignition Coil ‘F’, an open or shorted Ignition Coil ‘F’ harness, or a poor electrical connection in the Ignition Coil ‘F’ circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light and your engine is running rough, it could be due to a faulty Ignition Coil ‘F’, an open or shorted harness, or poor electrical connection.
Visually inspect the wiring harness and connectors for damage and check for broken, bent, pushed out, or corroded connector’s pins.
