The P2314 fault code in automobiles indicates a problem with the ignition coil ‘E’. This can cause the engine light to turn on and the engine to run rough. The cause of this issue could be a faulty ignition coil, an open or shorted harness, or a poor electrical connection.
It is important to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated to be around 1.0.
To interpret the fault code, one should check the possible causes listed above and look for any broken or bent components.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2314: Ignition Coil Secondary Circuit – Symptoms & Solutions
If you’re experiencing an illuminated engine light and rough engine performance, read on to learn more about the symptoms of the p2314 automobile fault code.
- The P2314 fault code in an automobile can cause the following symptoms: the engine light will turn on or the service engine soon warning light will appear.
- The engine may start running rough, causing a noticeable decrease in performance.
- The vehicle may also experience a lack of power or acceleration.
- Additionally, the engine may misfire or stall, and there may be a noticeable decrease in fuel efficiency.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2314: Ignition Coil Secondary Circuit – Culprits Unveiled!
P2314 fault code in automobiles can be caused by a faulty ignition coil, open or shorted harness, or poor electrical connection.
- The automobile fault code P2314 can be caused by a faulty ignition coil ‘E’.
- It can also be caused by an open or shorted ignition coil ‘E’ harness.
- Additionally, a poor electrical connection in the ignition coil ‘E’ circuit can also trigger this fault code.
Fix Code P2314: Simple Steps To Get Your Car Running
To fix the p2314 automobile fault code, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2314, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2314: Affordable Fix For Your Car’s Ignition System
The fault code is P2314. The estimated repair time is 1.0 hour.
The cost of fixing the fault code is influenced by the repair time.
Most auto repair shops charge between $75 and $150 per hour.
Therefore, the cost of fixing the P2314 fault code can range from $75 to $150.
P2314: Ignition Coil ‘e’ Secondary Circuit – Faulty Connection
The P2314 code is related to the ignition coil ‘E’ secondary circuit. The Powertrain Control Module (PCM) controls the current flow through the primary ignition coil. The PCM provides a switched ground path through the ignition coil driver to ground.
The P2314 code sets when the PCM detects a short to voltage in the circuit.
The PCM continuously monitors the ignition system for concerns. The high voltage surge creates a flyback voltage which the PCM uses as a feedback during the ignition diagnostics.
FAQ
If you see the engine light on or the service engine soon warning light, and the engine is running rough, it could be due to the P2314 fault code. This code is caused by a faulty ignition coil ‘E’, an open or shorted ignition coil ‘E’ harness, or a poor electrical connection in the ignition coil ‘E’ circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
To visually inspect the related wiring harness and connectors for the fault code P2314, check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This fault code may cause the engine light to turn on and the engine to run rough due to a faulty ignition coil ‘E’, an open or shorted ignition coil ‘E’ harness, or a poor electrical connection in the ignition coil ‘E’ circuit. Check the possible causes listed above before proceeding with the inspection.
If you see the Engine Light ON or Service Engine Soon Warning Light, and your engine is running rough, it could be due to the P2314 fault code. This code is caused by a faulty Ignition Coil ‘E’, an open or shorted harness, or a poor electrical connection in the Ignition Coil ‘E’ circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light and the engine is running rough, it could be due to a faulty Ignition Coil ‘E’, an open or shorted harness, or poor electrical connection.
Check the wiring harness and connectors for damage and inspect the components for any issues.
