The P2134 fault code in automobiles refers to a problem with the Accelerator Pedal Position (APP) Sensor. The most common symptom is the Engine Light turning on.
The cause of this issue could be a faulty APP sensor, an open or shorted APP sensor harness, a poor electrical connection in the APP sensor circuit, or a faulty Powertrain Control Module (PCM).
The importance of repairing this issue lies in the fact that it affects the vehicle’s acceleration and performance. The repair difficulty is moderate, and the repair time is estimated to be around 1.0 hour.
To fix the issue, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P2134: Unresponsive Accelerator Pedal – Symptoms Explained
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2134 fault code. Here are the symptoms to look out for:
- The P2134 fault code in an automobile can cause several symptoms.
- These include the engine light turning on or the service engine soon warning light appearing.
- The vehicle may experience a reduction in power or acceleration, and the throttle may become unresponsive.
- The engine may also stall or hesitate during acceleration.
- Additionally, the vehicle may experience rough idling or poor fuel economy.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2134: Uncovering The Culprits Behind The Fault Code
The automobile fault code p2134 can be caused by a range of issues, including a faulty APP sensor and poor electrical connections.
- The automobile fault code P2134 can be caused by a faulty Accelerator Pedal Position (APP) Sensor.
- It can also be caused by an open or shorted Accelerator Pedal Position (APP) Sensor harness.
- Another cause can be a poor electrical connection in the Accelerator Pedal Position (APP) Sensor circuit.
- Lastly, a faulty Powertrain Control Module (PCM) can also cause the P2134 fault code.
Fixing P2134: Simple Steps To Solve The Issue
Below are some possible fixes for the automobile fault code p2134, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p2134, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2134: Affordable Fix For Complex Automobile Fault Code
The fault code P2134 is related to the throttlepedal position sensorswitch.
The diagnosis cost may vary depending on the auto repair shop, but it is usually charged per hour.
The estimated repair time for this fault code is 1.0 hour. The fixing cost may range between $75 and $150 per hour, depending on the auto repair shop.
It is important to note that the fixing cost may also vary depending on the severity of the issue and the parts that need to be replaced.
P2134: Throttle/Pedal Position Sensor/Switch ‘f’ Circuit Intermittent
The P2134 code refers to a problem with the ThrottlePedal Position SensorSwitch ‘F’ Circuit Intermittent. The Accelerator Pedal Position (APP) sensor is an input to the Powertrain Control Module (PCM) and used to determine the amount of torque requested by the operator.
There are 2 pedal position signals in the sensor, APP and APP2, which have a positive slope but are offset and increase at different rates. If a concern is present with one of the circuits, the other input is used. There are 2 reference voltage circuits, 2 signal return circuits, and 2 signal circuits between the PCM and the APP sensor assembly.
The pedal position signal is converted to pedal travel degrees by the PCM, which is the input to the torque based strategy.
FAQ
If you see the engine light on or service engine soon warning light, it could be due to the P2134 fault code. This code is caused by a faulty Accelerator Pedal Position (APP) Sensor, an open or shorted APP Sensor harness, a poor electrical connection in the APP Sensor circuit, or a faulty Powertrain Control Module (PCM). To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light with a P2134 fault code, it may be due to a faulty Accelerator Pedal Position (APP) Sensor, an open or shorted APP Sensor harness, a poor electrical connection in the APP Sensor circuit, or a faulty Powertrain Control Module (PCM). To fix the issue, visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Yes, it is necessary to visually inspect the wiring harness and connectors to fix the P2134 fault code. The fault code is caused by a faulty Accelerator Pedal Position (APP) Sensor, an open or shorted APP Sensor harness, a poor electrical connection in the APP Sensor circuit, or a faulty Powertrain Control Module (PCM). To fix the issue, it is recommended to check the possible causes listed above and visually inspect the related wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Accelerator Pedal Position (APP) Sensor, APP Sensor harness being open or shorted, APP Sensor circuit poor electrical connection, or a faulty Powertrain Control Module (PCM).
Check the possible causes, visually inspect the related wiring harness and connectors, and look for damaged components or corroded connector’s pins.
