If you’re experiencing a lack of response from your throttle pedal and your engine light is on, it could be due to the P2133 fault code. This code indicates a problem with the Accelerator Pedal Position (APP) Sensor or its circuitry.
The cause could be a faulty sensor, an open or shorted harness, or a poor electrical connection. It’s important to address this issue promptly as it can affect your vehicle’s performance and safety. The repair time for this issue is estimated at 1.0, and it’s recommended to visually inspect the wiring harness and connectors for any damage or corrosion.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P2133: Unresponsive Accelerator Pedal – Symptoms Explained
If you’re experiencing an illuminated engine light and unresponsive throttle pedal, read on to learn more about the symptoms of the p2133 automobile fault code.
- The automobile fault code P2133 has two main symptoms.
- The first symptom is that the engine light turns on.
- The second symptom is that there is no response from the throttle pedal.
- These symptoms are important to note as they can indicate a serious issue with the vehicle’s throttle system.
- It is important to have the vehicle inspected by a qualified mechanic as soon as possible to prevent further damage or safety hazards.
Decoding P2133: Common Culprits
The automobile fault code p2133 can be caused by a faulty APP sensor, open or shorted harness, poor electrical connection, or a faulty PCM.
- The automobile fault code P2133 can be caused by a faulty Accelerator Pedal Position (APP) Sensor.
- It can also be caused by an open or shorted Accelerator Pedal Position (APP) Sensor harness.
- Another cause can be a poor electrical connection in the Accelerator Pedal Position (APP) Sensor circuit.
- Lastly, a faulty Powertrain Control Module (PCM) can also cause the P2133 fault code.
Fix Code P2133: Simple Steps To Get Your Car Running
To fix the p2133 fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2133, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2133: Affordable Fix For Complex Automobile Fault Code
The fault code P2133 indicates a problem with the throttle or pedal position sensor. The estimated repair time for this issue is 1.0 hour.
The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.
Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
P2133: Throttle/Pedal Position Sensor/Switch ‘f’ Circuit High
The P2133 code is related to the Accelerator Pedal Position (APP) sensor. The sensor has two pedal position signals, APP and APP2, which have a positive slope and increase at different rates.
The PCM determines if a signal is incorrect by calculating where it should be, inferred from the other signals.
If a concern is present with one of the circuits, the other input is used.
The P2133 code indicates a problem with the ThrottlePedal Position SensorSwitch ‘F’ Circuit being too high.
FAQ
If you’re experiencing an engine light on or service engine soon warning light, along with no throttle pedal response, the fault code P2133 may be the culprit. This code is often caused by a faulty Accelerator Pedal Position (APP) Sensor, an open or shorted APP Sensor harness, a poor electrical connection in the APP Sensor circuit, or a faulty Powertrain Control Module (PCM). To fix the issue, it’s recommended to visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If your engine light is on and there is no throttle pedal response, it could be due to a faulty Accelerator Pedal Position (APP) Sensor or a related issue. One possible cause is an open or shorted APP Sensor harness. To identify this issue, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an engine light on or service engine soon warning light, along with no throttle pedal response, it could be due to a faulty Accelerator Pedal Position (APP) Sensor, an open or shorted APP Sensor harness, a poor electrical connection in the APP Sensor circuit, or a faulty Powertrain Control Module (PCM). To fix this, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector pins.
Wrap Up
If you experience no throttle pedal response and the engine light is on, it may be due to a faulty Accelerator Pedal Position (APP) Sensor or a poor electrical connection. Check the wiring harness and connectors for damage and inspect the components for any issues. Also, check the Powertrain Control Module (PCM) for faults.
