The P2130 fault code in automobiles refers to a problem with the Accelerator Pedal Position (APP) Sensor.
The most common symptom is the Engine Light turning on. The cause of this issue could be a faulty APP sensor, an open or shorted APP sensor harness, a poor electrical connection in the APP sensor circuit, or a faulty Powertrain Control Module (PCM). The importance of repairing this issue lies in the fact that it affects the vehicle’s acceleration and performance.
The repair difficulty is moderate, with a repair time of 1.0. To fix the issue, one must visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P2130: Unresponsive Pedal? Check These Symptoms Now!
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2130 fault code.
Here are the symptoms to look out for:
- The P2130 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include a decrease in engine power, a decrease in fuel efficiency, and difficulty starting the engine.
- The vehicle may also experience hesitation or stalling during acceleration, and the throttle may not respond properly.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
Decoding P2130: Common Culprits
The automobile fault code p2130 can be caused by a faulty accelerator pedal position sensor, open or shorted sensor harness, poor electrical connection, or a faulty powertrain control module.
- The automobile fault code P2130 can be caused by a faulty Accelerator Pedal Position (APP) Sensor.
- It can also be caused by an open or shorted Accelerator Pedal Position (APP) Sensor harness.
- Another cause can be a poor electrical connection in the Accelerator Pedal Position (APP) Sensor circuit.
- Lastly, a faulty Powertrain Control Module (PCM) can also cause the P2130 fault code.
Fix Code P2130: Simple Steps To Get Your Car Running
To fix the p2130 fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2130, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2130: Affordable Fix For Complex Automobile Fault Code
The fault code P2130 indicates a problem with the throttle or pedal position sensor.
The estimated repair time for this issue is 1.0 hour. The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour. Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
It is important to address this issue promptly to avoid further damage to the vehicle and ensure safe driving.
P2130: Throttle/Pedal Position Sensor/Switch ‘d’ Circuit Range/Performance
The P2130 fault code relates to the Accelerator Pedal Position (APP) sensor. The sensor has two pedal position signals, APP and APP2, which have a positive slope but increase at different rates. The PCM determines if a signal is incorrect by calculating where it should be, inferred from the other signals.
If a concern is present with one of the circuits, the other input is used. There are a total of 6 circuits and pins between the PCM and the APP sensor assembly.
The pedal position signal is converted to pedal travel degrees by the PCM, which is the input to the torque based strategy.
FAQ
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the P2130 fault code. This code is caused by a faulty Accelerator Pedal Position (APP) Sensor, an open or shorted APP Sensor harness, a poor electrical connection in the APP Sensor circuit, or a faulty Powertrain Control Module (PCM). To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON (or Service Engine Soon Warning Light) due to the P2130 fault code, you may have a faulty Accelerator Pedal Position (APP) Sensor or a poor electrical connection in the Accelerator Pedal Position (APP) Sensor circuit. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any open or shorted wires and ensure that the connections are secure.
If you find damaged components or broken, bent, pushed out, or corroded connector’s pins related to the P2130 fault code, follow these steps: Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify the cause of the problem and take the necessary steps to fix it.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Accelerator Pedal Position (APP) Sensor, APP Sensor harness being open or shorted, APP Sensor circuit poor electrical connection, or a faulty Powertrain Control Module (PCM). Check the possible causes, visually inspect the related wiring harness and connectors, and look for damaged components and connector’s pins.
