The P212C fault code in automobiles indicates a problem with the Throttle Position SensorSwitch. The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light.

The cause of this issue could be a faulty Throttle Position SensorSwitch, an open or shorted harness, or a poor electrical connection in the circuit. It is important to address this issue promptly as it can lead to reduced engine performance and fuel efficiency.

The repair process involves visually inspecting the wiring harness and connectors for any damage or corrosion.

The difficulty level of this repair is considered to be moderate, and it takes approximately 1.0 hour to fix. It is crucial to interpret the fault code accurately to ensure the correct repair is performed.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level6.67 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p212c fault code.

Here are the symptoms to look out for:

  • The P212C fault code in an automobile can cause several symptoms.
  • These include the engine light turning on or the service engine soon warning light appearing.
  • The vehicle may experience a decrease in power or acceleration.
  • The throttle may become unresponsive or have delayed response times.
  • The engine may also stall or have difficulty starting.
  • Additionally, the vehicle may experience poor fuel economy or emit excessive exhaust emissions.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code p212c can be caused by various factors, including a faulty throttle position sensorswitch and poor electrical connection.

  • The automobile fault code P212C can be caused by a faulty Throttle Position Sensor/Switch.
  • It can also be caused by an open or shorted Throttle Position Sensor/Switch harness.
  • Additionally, a poor electrical connection in the Throttle Position Sensor/Switch circuit can also trigger this fault code.

To fix the p212c automobile fault code, check the possible causes and inspect related wiring harness and connectors for damage.

  • To fix the automobile fault code p212c, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The fault code P212C indicates a problem with the throttle pedal position sensor.

The diagnosis involves checking the sensor’s wiring and connections, as well as testing the sensor’s output. The estimated repair time for this issue is 1.0 hour.

The cost of fixing this issue can vary depending on the auto repair shop, but it is common for most shops to charge between $75 and $150 per hour.

Therefore, the total cost of fixing the P212C fault code can range from $75 to $150.

The P212C fault code is related to the Throttle Position SensorSwitch ‘G’ Circuit.

The Engine Control Module (ECM) monitors this circuit and sets the OBDII Code when the signal is out of factory specifications. The P212C Code specifically indicates that the Throttle Position SensorSwitch ‘G’ Circuit signal is low. This fault code can cause issues with the vehicle’s acceleration and overall performance.

It is important to have this issue diagnosed and repaired by a qualified mechanic to ensure proper functioning of the vehicle.

What are the possible causes of the P212C automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P212C fault code. This code is usually caused by a faulty throttle position sensor/switch, an open or shorted throttle position sensor/switch harness, or a poor electrical connection in the throttle position sensor/switch circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P212C fault code?

If you’re experiencing an engine light or service engine soon warning light with a P212C fault code, it could be due to a faulty throttle position sensor/switch or poor electrical connection. To fix this issue, start by visually inspecting the related wiring harness and connectors. Check for any damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues and get your vehicle back on the road.

What are the signs of damaged components that I should look for when fixing the P212C fault code?

If you’re fixing the P212C fault code, look out for the engine light turning on or the service engine soon warning light. The cause of this issue could be a faulty throttle position sensor/switch, an open or shorted throttle position sensor/switch harness, or a poor electrical connection in the throttle position sensor/switch circuit. To fix this, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components such as broken, bent, pushed out, or corroded connector pins.

p212c error fault code explained

If your engine light is on and you have a P212C fault code, it’s likely due to a faulty throttle position sensorswitch or a poor electrical connection. To fix it, visually inspect the wiring harness and connectors for damage or corrosion and check for broken or bent pins.

Scroll to Top