The P2114 automobile fault code indicates a problem with the ThrottlePedal Position Sensor, which can cause the Engine Light to turn on. The possible causes of this issue include a faulty sensor, an open or shorted sensor harness, or a poor electrical connection in the sensor circuit. To fix this problem, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
The repair time for this issue is estimated to be around 1.0.
Understanding the fault code and its possible causes is crucial for maintaining the health of your vehicle.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 6.67 (Out of 10) |
P2114: Unresponsive Throttle – Symptoms & Solutions
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2114 fault code. Here are the symptoms to look out for:
- The P2114 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, hesitation or stalling during acceleration, and difficulty starting the engine.
- The vehicle may also experience rough idling or poor fuel economy.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P2114: Common Culprits
The automobile fault code p2114 can be caused by a faulty sensor, open or shorted harness, or poor electrical connection.
- The automobile fault code P2114 can be caused by a faulty Throttle/Pedal Position Sensor.
- It can also be caused by an open or shorted Throttle/Pedal Position Sensor harness.
- Additionally, a poor electrical connection in the Throttle/Pedal Position Sensor circuit can also trigger this fault code.
Fix Code P2114: Simple Steps To Get Your Car Running
To fix the p2114 automobile fault code, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2114, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2114: Affordable Fix For Complex Auto Fault Code
The automobile fault code P2114 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of fixing the P2114 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P2114: Throttle Actuator Control System – Stuck Open
The P2114 code is a generic description for ThrottlePedal Position Sensor ‘C’ Minimum Stop Performance. However, the manufacturer may have a different description for your specific vehicle.
Unfortunately, we do not have any further information on this code at this time. If you have any questions, please feel free to post them in the comments section below for more information.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the p2114 fault code. This code is usually caused by a faulty throttle or pedal position sensor, an open or shorted sensor harness, or a poor electrical connection in the sensor circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an engine light or service engine soon warning light with a p2114 fault code, it could be due to a faulty throttle/pedal position sensor, an open or shorted harness, or poor electrical connection. To fix this issue, start by visually inspecting the related wiring harness and connectors. Check for any damaged components and look for broken, bent, pushed out, or corroded connector’s pins.
If the Throttle/Pedal Position Sensor circuit has a poor electrical connection, it can cause the p2114 fault code. This is indicated by the engine light turning on or the service engine soon warning light. To fix this issue, check for possible causes such as a faulty sensor or an open or shorted harness. Visually inspect the wiring harness and connectors for any damage or corrosion, and check for broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on and showing the P2114 code, it may be due to a faulty throttlepedal position sensor or poor electrical connection.
To fix it, visually inspect the wiring harness and connectors for damage or corrosion and check for broken or bent pins.
