If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the P2078 fault code. This code indicates a problem with the Intake Manifold Tuning Valve Position SensorSwitch, which can be caused by a faulty sensor, poor electrical connection, or a damaged wiring harness. It’s important to address this issue promptly as it can affect the performance of your vehicle.
The repair time for this fault code is estimated at 1.0, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
P2078: Uncovering The Symptoms Of A Faulty Throttle Actuator Control Module
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2078 fault code. Here are the symptoms to look out for:
- The P2078 fault code in an automobile can cause several symptoms.
- The most common symptom is the illumination of the engine light or service engine soon warning light.
- Other symptoms include a decrease in engine power, rough idling, stalling, and poor acceleration.
- The vehicle may also experience misfires, hesitation, and reduced fuel efficiency.
- Additionally, the engine may emit unusual noises or vibrations, and the transmission may shift roughly or erratically.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2078: Fuel Injector Circuit Low – Common Causes
The automobile fault code P2078 can be caused by various factors, including faulty sensors, poor electrical connections, and malfunctioning control modules.
- The automobile fault code P2078 can be caused by a faulty Intake Manifold Tuning Valve Position Sensor/Switch.
- It can also be caused by an open or shorted harness of the Intake Manifold Tuning Valve Position Sensor/Switch.
- A poor electrical connection in the Intake Manifold Tuning Valve Position Sensor/Switch circuit can also trigger the fault code.
- Another cause is a faulty Intake Manifold Tuning Valve (IMTV).
- A faulty Intake Manifold Runner Control (IMRC) can also cause the fault code.
- Lastly, a faulty Powertrain Control Module (PCM) can trigger the P2078 fault code.
Fix Code P2078: Quick Steps To Get Your Car Running
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
To fix the p2078 automobile fault code, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2078, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- Ensure that all the connections are secure and free of corrosion.
- This repair should take approximately 1.0 hour.
P2078: Affordable Fix For Your Car’s Performance Woes
The fault code P2078 indicates a problem with the intake manifold tuning valve. The diagnosis process involves checking the valve’s electrical connections and vacuum lines. The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this issue varies depending on the auto repair shop, but it is common to charge between $75 and $150 per hour.
Other factors that may influence the cost include the severity of the problem and the type of vehicle.
P2078: Fuel Injector Control Circuit Low – What You Need To Know
The P2078 code refers to the Intake Manifold Tuning Valve (IMTV) system. The IMTV is a motorized actuated unit mounted directly to the intake manifold. The IMTV actuator controls a shutter device attached to the actuator shaft.
The code indicates a problem with the IMTV position sensorswitch circuit on Bank 1.
The IMTV system is monitored for failure during continuous, Key ON Engine OFF (KOEO), or Key ON Engine Running (KOER) self-tests.
The test fails when the signal is more or less than an expected calibrated range. The motorized IMTV unit will not be energized below approximately 2600 rpm or higher on some vehicles.
The shutter will be in the closed position not allowing airflow blend to occur in the intake manifold. Above approximately 2600 rpm or higher, the motorized unit will be energized.
FAQ
If your engine light is on and you’re getting the P2078 fault code, it could be due to a faulty Intake Manifold Tuning Valve Position Sensor/Switch, an open or shorted harness, poor electrical connection, a faulty Intake Manifold Tuning Valve (IMTV), a faulty Intake Manifold Runner Control (IMRC), or a faulty Powertrain Control Module (PCM). To fix the issue, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light with a P2078 fault code, it may be due to a faulty Intake Manifold Tuning Valve Position Sensor/Switch, open or shorted harness, poor electrical connection, faulty IMTV, IMRC, or PCM. To fix it, check the possible causes listed above, visually inspect the wiring harness and connectors, and look for damaged components or corroded connector pins.
If you’re experiencing the P2078 fault code, indicated by the Engine Light ON or Service Engine Soon Warning Light, you should visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. Additionally, check the possible causes listed above, including a faulty Intake Manifold Tuning Valve Position Sensor/Switch or Intake Manifold Tuning Valve.

Wrap Up
If your engine light is on, it could be due to a faulty Intake Manifold Tuning Valve Position SensorSwitch, IMTV, IMRC, or PCM. Check the possible causes listed above, inspect the wiring harness and connectors, and look for damaged components or corroded pins.