The P2043 fault code in automobiles indicates a problem with the Reductant Temperature Sensor. The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light.
The cause of this issue could be a faulty sensor, an open or shorted harness, or a poor electrical connection. It is important to address this issue promptly as it can lead to reduced fuel efficiency and increased emissions. The repair process involves visually inspecting the wiring harness and connectors for any damage or corrosion.
The difficulty level of this repair is considered to be moderate, and it typically takes around 1.0 hour to fix. To interpret the fault code, it is recommended to check the “Possible Causes” listed above and inspect the related components thoroughly.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2043: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2043 fault code.
Here are the symptoms to look out for:
- The P2043 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include a decrease in engine performance, reduced fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in power when accelerating.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2043: Fuel Pressure Sensor Circuit Malfunction Causes
P2043 fault code can be caused by a faulty sensor, open or shorted harness, or poor electrical connection.
- The automobile fault code P2043 can be caused by a faulty Reductant Temperature Sensor.
- It can also be caused by an open or shorted Reductant Temperature Sensor harness.
- Additionally, a poor electrical connection in the Reductant Temperature Sensor circuit can also trigger this fault code.
Fix P2043: Simple Steps To Solve The Issue
To fix the automobile fault code p2043, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2043, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2043: Affordable Fix For Your Car’s Fuel System
The automobile fault code P2043 indicates a problem with the diesel particulate filter pressure sensor circuit.
The estimated repair time for this issue is 1.0 hour. The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour. Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
P2043: Fuel Temperature Sensor Circuit High Input
The P2043 code is related to the reductant heater and sender assembly in a vehicle. This assembly contains a pickup tube for the reductant pump module, an electric heating element, a reductant temperature sensor, and an electrode type level sensor.
When the reductant temperature sensor detects the diesel exhaust fluid temperature dropping to the freezing point of 12°F (-11°C), the PCM will command the glow plug control module to provide voltage to the heating element. The heating element thaws liquid reductant within the reductant heater and sender assembly reservoir during cold ambient temperatures. The P2043 code indicates an issue with the reductant temperature sensor circuit range or performance.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P2043 fault code. This code is caused by a faulty reductant temperature sensor, an open or shorted reductant temperature sensor harness, or a poor electrical connection in the reductant temperature sensor circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to a faulty Reductant Temperature Sensor or an open/shorted harness. To fix this issue, start by visually inspecting the wiring harness and connectors related to the sensor. Check for any damaged components and look for broken, bent, pushed out, or corroded connector pins. This will help you identify any poor electrical connections and get your vehicle back on track.
Ignoring the P2043 fault code in your automobile can lead to serious consequences. The engine light or service engine soon warning light will remain on, indicating a problem with the reductant temperature sensor. This can result in decreased fuel efficiency, increased emissions, and potential damage to the engine. It is important to visually inspect the wiring harness and connectors and check for damaged components to avoid further complications.
Wrap Up
If your engine light is on, it could be due to a faulty Reductant Temperature Sensor, an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion. Check for broken, bent, or pushed out pins.
