The P1FE6 automobile fault code indicates a problem with the HybridEV Battery Interface Control Module. The most common symptom is the Engine Light turning on. The cause of this issue could be a faulty HybridEV Battery Interface Control Module, an open or shorted harness, or a poor electrical connection.
It is important to address this issue promptly as it can affect the performance of the vehicle.
The repair difficulty is moderate, and it takes approximately 1.0 hour to fix.
To interpret the fault code, one should check the possible causes listed above and visually inspect the related wiring harness and connectors.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
P1Fe6: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1fe6 fault code.
Here are the symptoms to look out for:
- The P1FE6 fault code in automobiles can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light, and other warning lights may illuminate on the dashboard.
- The engine may run rough or stall, and there may be a decrease in power or acceleration.
- The vehicle may also experience reduced fuel efficiency, and there may be a noticeable increase in emissions.
- Additionally, the transmission may shift poorly or erratically, and there may be a loss of communication with other vehicle systems.
- It is important to address these symptoms promptly to avoid further damage to the vehicle.
Decoding P1Fe6: Common Causes Of The Fault Code
P1FE6 fault code can be caused by issues with the HybridEV Battery Interface Control Module or its circuit connections.
- The automobile fault code P1FE6 can be caused by a faulty Hybrid/EV Battery Interface Control Module.
- It can also be caused by an open or shorted Hybrid/EV Battery Interface Control Module harness.
- Additionally, a poor electrical connection in the Hybrid/EV Battery Interface Control Module circuit can also trigger this fault code.
Fix Code P1Fe6: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1fe6, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p1fe6, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1Fe6 Fixing Cost And Complexity
The fault code P1FE6 indicates an issue with the hybrid battery pack. The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour. Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
It is important to address this issue promptly to avoid further damage to the vehicle and ensure its safe operation.
P1Fe6: Your Car’s Fuel System Needs Attention
The P1FE6 code is related to the hybrid battery in a vehicle. The battery contains 192 individual cells, which are electrically connected in series. There are three distinct sections of the battery, each containing a different number of cell groups.
The battery energy control module monitors the voltage of the 96 battery cell groups. The P1FE6 code indicates a fault condition in the HybridEV Battery Interface Control Module 8 Voltage Sensor Circuit, specifically a high voltage reading. This information is communicated to the hybrid powertrain control module 2 for diagnostic trouble code information.
FAQ
If you’re experiencing the P1FE6 fault code, your engine light may be on. This could be due to a faulty Hybrid/EV Battery Interface Control Module, an open or shorted harness, or poor electrical connection in the circuit. To fix this issue, check the possible causes listed above, visually inspect the wiring harness and connectors, and look for any damaged components or corroded pins.
If you’re experiencing the P1FE6 fault code, it’s likely that your engine light is on. This could be due to a faulty Hybrid/EV Battery Interface Control Module, an open or shorted harness, or poor electrical connection. To fix the issue, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the P1FE6 fault code, you may notice that your engine light is on. This could be due to a faulty Hybrid/EV Battery Interface Control Module, an open or shorted harness, or poor electrical connection. To troubleshoot this issue, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, or pushed out pins on the connectors. Be sure to address any issues you find to fix the problem.
![p1fe6 error fault code explained](https://carmodnerd.com/wp-content/uploads/2023/06/P1FE6-error-fault-code.jpg)
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty HybridEV Battery Interface Control Module, an open or shorted harness, or poor electrical connection. Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.